Proto Shield (Prototype) for Arduino Uno Mini Breadboard
₹81.18 + GST
2 in stock
2 in stock
- It has a nice standard 0.1?x0.1? prototyping grid with big pads
- Comes with Stacking headers and plain header, choose whichever you want when soldering together
- An IC pattern for adding DIP ICs up to 20 pins
- Power rails down the middle and sides
- A reset button and an extra general use button
- Two 3mm general use LEDs, red and green, as well as 2 matching resistors
You must be logged in to post a review.
Related products
Electromagnetic Buzzer – 5V – PCB Mount
₹12.22 + GSTAdd to cartThis is a Small PCB Mountable 5V Active Electromagnetic Buzzer. It is great to add Audio Alert to your electronic designs. It operates on 5V supply, uses a coil element to generate an audible tone.
NEO-6M GPS Module with EPROM
₹220.58 + GSTAdd to cart- This is a complete GPS module that is based on the NEO 6M GPS. This unit uses the latest technology to give the best possible positioning information and includes a larger built-in 25 x 25mm active GPS antenna with a UART TTL socket. A battery is also included so that you can obtain a GPS lock faster. This is an updated GPS module that can be used with ardupilot mega v2. This GPS module gives the best possible position information, allowing for better performance with your Ardupilot or other Multirotor control platform.
- The GPS module has serial TTL output, it has four pins: TX, RX, VCC, and GND. You can download the u-centre software for configuring the GPS and changing the settings and much more. It is really good software (see link below).
?
- Add to cart
Arduino UNO R3 SMD is the open source Embedded Development board launched by Arduino based on Atmega328 SMD Package Microcontroller.?Because Atmel is moving more and more of their production capacity to surface mount ICs, the DIP packaged ATmega is becoming more and more difficult to get.
- Add to cart
Features:
- With reverse polarity protection, high current protection high temperature fr-4 circuit board
- Maximum power: 2000w
- voltage: Ac 110-220v
- voltage regulation: Ac 50-220v
- size(lx w): Approx. 46 x 35mm
- how to use: This product series with the lamp or electrical circuit, table lamps, appliances disconnect any firewire or zero line (ie a product two wires connected to both) rotary potentiometer spin rod, you can play light and shade adjustment, speed, pressure, the role of the thermostat, use very convenient. This product is applicable to: The use of new two-way high-power thyristor can be very convenient to adjust the mains current up to 25 a, and solve the the overcurrent problem of the heating wire resistance is too small in the case of cooling causing good, the output voltage is adjusted anywhere between 90 to 220 volts for use with electrical appliances. Such as: Electric stove, water heater tune thermal, lighting dimmer, small motor speed, electric iron thermostat. So as to achieve dimming, thermostats, pressure regulator effect. Large appliances available, power consumption is less than 2, 000 watts of power has sufficient home appliances or small factories. (Inductive or capacitive load power should be reduced, the regulator is equipped with two-way high-power thyristor, potentiometers are with nuts, do not have to add any components will be able to use, very convenient and practical).
- Add to cart
The Arduino Mega 2560 R3 is an open source precise microcontroller board Successor to the Arduino Mega based on the ATmega2560 SMD chip.The Mega 2560 R3 also adds SDA and SCL pins next to the AREF. In addition, there are two new pins placed near the RESET pin. One is the IOREF that allow the shields to adapt to the voltage provided from the board. The other is a not connected and is reserved for future purposes. The Mega 2560 R3 works with all existing shields but can adapt to new shields which use these additional pins.
Reviews
There are no reviews yet.