CH340G USB To TTL(Serial) Converter For Arduino Nano Raspberry Pi
Original price was: ₹100.00.₹78.00Current price is: ₹78.00. + GST
8 in stock
8 in stock
3 in stock
2 in stock
29 in stock
- Built-in USB to TTL Transfer chip.
- Designed to be used for USB to TTL electronic projects.
- TTL interface output, easy to connect to your MCU.
- Dual 3.3V and 5V Power output, work with 3.3v and 5 V target device.
- The mini-module is designed specifically for STC download and ARDUINO PRO supports all series of STC
- Supports WIN7/VISTA/MAC/LINUX(32 bit /64-bit system)
You must be logged in to post a review.
Related products
-
8 Channel 5V Relay Board Expansion Module Optocoupler compatible UNO Raspberry
Original price was: ₹312.00.₹246.16Current price is: ₹246.16. + GSTAdd to cartSpecification
- This relay module is 5 Volts active low.
- It is an 8-channel relay interface board, which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, PLC, etc.
- It is also able to control various appliances and other equipments with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Standard interface can be directly connected with microcontrollers.
- Red working status indicator lights are conducive to the safe use.
- Widely used for all MCU control, industrial sector, PLC control, smart home control.
- Input port IN1, IN2, IN3, IN4, IN5, IN6, IN7, IN8 low signal level effectively.
- VCC, GND : Input power.
- JD – VCC : Relay power input port,relay can power alone.
- Working voltage : 5V
- Module weight : about 112g
- package weight : about 150g
- module size : about 1.7cm X 5.5cm X 13.7cm(height * width * long)
-
Thermoelectric Peltier Cooler or Cooling Module 12V 92W Max
Original price was: ₹300.00.₹174.20Current price is: ₹174.20. + GSTAdd to cartThermoelectric coolers (TEC or Peltier) create a temperature differential on each side. One side gets hot and the other side gets cool. Therefore, they can be used to either warm something up or cool something down, depending on which side is used. You can also use temperature differential to generate electricity.
-
L298 Dual Full Bridge Driver
Original price was: ₹110.00.₹88.05Current price is: ₹88.05. + GSTAdd to cartThe?L298?is an integrated monolithic circuit in a 15- lead Multiwatt and Power SO20 packages. It is a high voltage, high current dual full-bridge driver designed to accept standard TTL logic levels and drive inductive loads such as relays, solenoids, DC and stepping motors. Two enable inputs are provided to enable or disable the device independently of the input signals. The emitters of the lower transistors of each bridge are connected together and the corresponding external terminal can be used for the connection of an external sensing resistor. An additional supply input is provided so that the logic works at a lower voltage.
-
DS1307 Real Time Clock (RTC) I2C IIC Module AT24C32 without Battery
Original price was: ₹80.00.₹48.90Current price is: ₹48.90. + GSTAdd to cartThis is Tiny RTC Real Time Clock DS1307 I2C IIC Module for Arduino. It contains a DS1307 real-time clock IC with a backup battery. It?s one of the easiest to use RTCs out there, with Arduino and other libraries or simply use I2C commands to set and retrieve the time and date. Includes a lithium coin cell battery which should be good for?four years?at least.
-
SIM800L GPRS GSM Module Micro SIM Card Core Board Quad-band TTL Serial Port (3.7-4.2V)
Original price was: ₹400.00.₹236.16Current price is: ₹236.16. + GSTRead moreFeatures
- Quad-band 850/900/1800/1900MHz ? connect onto any global GSM network with any 2G SIM (in the USA, T-Mobile is suggested).
- Make and receive voice calls using a headset or an external 8? speaker and electret microphone.
- PWM/Buzzer vibration motor control
- AT command interface with ?auto baud? detection
- Send and receive SMS messages.
- Send and receive GPRS data (TCP/IP, HTTP, etc.).
- Scan and receive FM radio broadcasts.
- Lead out buzzer and vibration motor control port.
- AT command interface with ?auto baud? detection.
- Onboard IPEX socket that can be connected to external antenna.
- Breakouts for external 8W speaker and electret mic if you don?t want to use a headphone
- Level shifting circuitry so you can run it with 2.8V to 5V logic.
- Vibrational motor (buzzer) driver so you can have noiseless notifications
- uFL or SMA connections for external antenna
- Indicator LEDs for power and network connectivity
- Standard SIM slides into the back
Reviews
There are no reviews yet.