7x7mm 6 Pin DPDT Self-Lock lock Push Switch
₹5.20 + GST
The mini push button 6 pin switch is useful in controlling power connections most of the time. The blue coloured square push button is DIP through-hole for mounting on PCB.
134 in stock
Purchase & earn 5 SmartX Rewards Coin!- Switch type: Non-Momentary
- Small? 7 x 7 mm. Size
- PCB through-hole mounting
- Maximum voltage DC30V
- Operating Current 0.1 A
12 reviews for 7x7mm 6 Pin DPDT Self-Lock lock Push Switch
You must be logged in to post a review.
Related products
- Rated 4.56 out of 5
Quartz Crystal Oscillator 16MHz HC-49S 2 Pin for TV, car Electronics, PC Card, Electronic Watch, DVD, MP3v
₹15.00₹6.72 + GSTPurchase & earn 7 SmartX Rewards Coin!Add to cartBuy nowCrystal Oscillators are used as a quick and easy way to offer circuits a very accurate and consistent frequency output. This 16 MHz Crystal is a thru-hole type and is typically used with microcontrollers. Optocoupler High Level Relay Module Board 5V 4-CH for PIC ARM DSP AVR | Compatible with Arduno NodeMCU Raspberry Pi | Pack of 1 | Blue (Excellent Quality)
₹139.00₹136.50 + GSTPurchase & earn 137 SmartX Rewards Coin!Add to cartBuy nowSpecification
- Size : 75mm (length) x 55mm (W) x 19.3mm (height);
- Weight : 80g;
- PCB Color : Blue;
- board four weeks with four screw holes, hole diameter 3.1mm, easy to install and fixed;
- Relay selection of quality loose music relays, SPDT. A common terminal, a normally open, one normally closed terminal;
- optocoupler isolation, good anti-jamming;
- Low pull, high release. Energisation status indicator light, release status LED is off;
- VCC for the system power, JD_VCC for the relay power. Default hair 12V relay, plug the jumper cap to;
- Relay Maximum output : DC 30V/10A, AC 250V/10A
- Wiring : VCC : positive power supply system GND : System power supply negative IN1 ? IN4 : relay control ports
- Purchase & earn 1 SmartX Rewards Coins!Add to cartBuy now
It is one of the most popular and long lived switching diodes because of its dependable specifications and low cost. The 1N4148 is useful in switching applications up to about 100 MHz. The 1N4148 comes in a DO-35 glass package for thru-hole mounting.
- Purchase & earn 2 SmartX Rewards Coin!Add to cartBuy now
BC327 is a general purpose PNP BJP transistor that can be used for switching and amplification purposes in electronic circuits. The transistor features 800mA collector current hence it can be used to drive variety of loads in an electronic application. The max collector-emitter voltage is -45V therefore it can easily handle load voltage under 45V. Apart from that transistor also features 625mW collector dissipation and DC current gain of maximum 630 therefore it can also be used as an audio amplifier or for any type of signal amplification.
- Purchase & earn 15 SmartX Rewards Coin!Add to cartBuy now
This DC Voltage Sensor Module is essentially a 5:1 potential divider circuit built using precession resistors for high accuracy.
The Arduino analog input is limited to a 5 VDC input.? If you wish to measure higher voltages,this module allows you to measure voltages of 0-25V. Keep in mind, you are restricted to voltages that are less than 25 volts. More than that and you will exceed the voltage limit of your Arduino input.
Rahul (verified owner) –
Less cost than other websites
Harsh (verified owner) –
Online best cost electronic components
Roma (verified owner) –
I got my project done with these components Great Support
Prakash (verified owner) –
Best cost electronic components in India
Devendra (verified owner) –
Drone parts i ordered and found ok
Prakash (verified owner) –
Very well worth the money.
Paaji (verified owner) –
Good techinical knowledge
Akshay (verified owner) –
The product is firmly packed.
Shubham (verified owner) –
I got my project done with these components Great Support
Er.Prashant (verified owner) –
Good techinical knowledge
Shubham (verified owner) –
Very well worth the money.
Priya (verified owner) –
Online best cost electronic components