BC327 PNP General Purpose Amplifier Transistor
Original price was: ₹5.00.₹1.95Current price is: ₹1.95.
BC327 is a general purpose PNP BJP transistor that can be used for switching and amplification purposes in electronic circuits. The transistor features 800mA collector current hence it can be used to drive variety of loads in an electronic application. The max collector-emitter voltage is -45V therefore it can easily handle load voltage under 45V. Apart from that transistor also features 625mW collector dissipation and DC current gain of maximum 630 therefore it can also be used as an audio amplifier or for any type of signal amplification.
210 in stock
- Package Type: TO-92
- Transistor Type: PNP
- Max Collector Current(IC): -800mA
- Max Collector-Emitter Voltage (VCE): -45V
- Max Collector-Base Voltage (VCB): -50V
- Max Emitter-Base Voltage (VBE): -5V
- Max Collector Dissipation (Pc): 625 Milliwatt
- Max Transition Frequency (fT): 100 MHz
- Minimum & Maximum DC Current Gain (hFE): 100 to 630
- Max Storage & Operating temperature Should be: -55 to +150Centigrade
1 review for BC327 PNP General Purpose Amplifier Transistor
You must be logged in to post a review.
We deliver all across India.
✅ Orders leave warehouse in 1–2 days.
✅ Delivery within 5–10 days after dispatch.
Related products
L298N Motor Driver Controller Board
It can control upto 4 DC motors, or 2 DC motors with directional and speed control. It can drive motors upto 46V with a total DC current of up to 4A. You can connect the two channels in parallel to double the maximum current or in series to double the maximum input voltage. Perfect for use in various electronics projects in India, L298N Motor Driver Controller Board Module | Dual H-Bridge DC Stepper Driver for Arduino | NodeMCU | Raspberry Pi Development Board - ensures reliability and performance. Ideal for various electronics projects, L298N Motor Driver Controller Board Module | Dual H-Bridge DC Stepper Driver for Arduino | NodeMCU | Raspberry Pi Development Board - offers quality and performance.
HC-05 Bluetooth Module
Bluetooth module (SMD) using chipsets BlueCore4 CSR. It has seven I / O ports, 8 Mbit flash memory for software storage and two modes of operation: via AT commands and transparently. In transparent mode it can be configured as Master, Slave or Loopback, and can connect to other devices that support SPP. In the AT command mode, the user can configure the module and send commands. By controlling the logic level of pin PIO11, the user can activate the work mode between AT command and transparent. Perfect for use in various electronics projects in India, HC-05 Bluetooth Module ensures reliability and performance. Ideal for various electronics projects, HC-05 Bluetooth Module offers quality and performance.
16 x 2 (1602) Character Blue LCD Display
- Operating Voltage is 4.7V to 5.3V
- Current consumption is 1mA without backlight
- Alphanumeric LCD display module, meaning can display alphabets and numbers
- Consists of two rows and each row can print 16 characters.
- Each character is build by a 58 pixel box
- Can work on both 8-bit and 4-bit mode
- It can also display any custom generated characters
- Available in Blue Backlight
Perfect for use in various electronics projects in India, 16 x 2 (JHD162A) Blue/White color DC 5V Character LCD display module FOR ALL TYPE OF DEVLOMENT BOARD ensures reliability and performance. Ideal for various electronics projects, 16 x 2 (JHD162A) Blue/White color DC 5V Character LCD display module FOR ALL TYPE OF DEVLOMENT BOARD offers quality and performance.
650nm 6mm 5V DC 5mW Mini Laser Dot Diode Module
- This 3 Volt 5mW 650nm Laser Diodeis a fun little red laser that emits a laser beam similar to a laser pointer when given 3 Volts of power just like you'd get from two standard AAA or AA batteries.
Perfect for use in various electronics projects in India, 650 nm 6 mm 5V 5 mW Mini Laser Dot Diode Module Head WL (Red) ensures reliability and performance. Ideal for various electronics projects, 650 nm 6 mm 5V 5 mW Mini Laser Dot Diode Module Head WL (Red) offers quality and performance.
Voltage Sensor Module
This DC Voltage Sensor Module is essentially a 5:1 potential divider circuit built using precession resistors for high accuracy.
The Arduino analog input is limited to a 5 VDC input. If you wish to measure higher voltages,this module allows you to measure voltages of 0-25V. Keep in mind, you are restricted to voltages that are less than 25 volts. More than that and you will exceed the voltage limit of your Arduino input. Perfect for use in various electronics projects in India, Voltage Sensor Module 25V ensures reliability and performance. Ideal for various electronics projects, Voltage Sensor Module 25V offers quality and performance.
Original Flex sensor 2.2 inches for Motion and Diy
Flex sensors are usually available in two sizes. One is 2.2 inch and another is 4.5 inch. Although the sizes are different the basic function remains the same. They are also divided based on resistance. There are LOW resistance, MEDIUM resistance and HIGH resistance types. Choose the appropriate type depending on requirement. Here we are going to discuss 2.2inch Flex sensor that is FS-L-0055. Perfect for use in various electronics projects in India, Original Flex sensor 2.2 inches for Motion and Diy ensures reliability and performance. Ideal for various electronics projects, Original Flex sensor 2.2 inches for Motion and Diy offers quality and performance.
8 Channel 5V Relay Board Expansion Module Optocoupler compatible UNO Raspberry
Specification
- This relay module is 5 Volts active low.
- It is an 8-channel relay interface board, which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, PLC, etc.
- It is also able to control various appliances and other equipments with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Standard interface can be directly connected with microcontrollers.
- Red working status indicator lights are conducive to the safe use.
- Widely used for all MCU control, industrial sector, PLC control, smart home control.
- Input port IN1, IN2, IN3, IN4, IN5, IN6, IN7, IN8 low signal level effectively.
- VCC, GND : Input power.
- JD - VCC : Relay power input port,relay can power alone.
- Working voltage : 5V
- Module weight : about 112g
- package weight : about 150g
- module size : about 1.7cm X 5.5cm X 13.7cm(height * width * long)
Perfect for use in various electronics projects in India, 8 Channel 5V Relay Board Expansion Module Optocoupler compatible UNO Raspberry ensures reliability and performance. Ideal for various electronics projects, 8 Channel 5V Relay Board Expansion Module Optocoupler compatible UNO Raspberry offers quality and performance.
Er.Prashant (verified owner) –
Good quality.