Please Note we are only providing kit we marked as ACTUAL PRODUCT, project shown customer needs to do at there own we just provide reference.

Abstract:

Fire Indication System circuit is presented here is based on the readily available Flame Sensor, comparator IC LM393. The Flame sensor is used as the fire intensity detector while IC LM393 used as comparator. In the absence of fire, no fire on the flame sensor. As a result flame sensor stop conducting and LED stays off. However, when there is fire on the flame sensor, flame sensor starts conducting and LED glows.

Application of the circuit:

Most of the flame sensor based circuits available in market use one or another kind of flame sensor which increases the cost and also require complicated circuitry around it. But this flame sensor based circuit uses readily available flame sensor as fire detector. The functioning of this Fire Indication System circuit is to detect fire and automatically activate the LED in presence of fire. LED glows continuously indicating the presence of fire till there is fire.

Why this particular circuit:

Flame sensor used here as a fire detector. The circuit operates normally over a DC voltage of 5V which can be obtained by DC supply cable.

Explained working of circuit:

The basic idea behind the circuit operation is to turn ON LED in presence of fire. The flame sensor is needed for this purpose. Flame sensor is device that converts heat to electric energy. Here, Fire Indication System circuit works as fire detector while flame sensor turns on the LED. IC LM393 is used as comparator. Flame sensor output is connected as input to comparator. Pin no. 4 of LM393 is pulled towards ground. In normal condition, when there is no fire and LED stays off. Now consider second scenario when there is fire, the LED glows in the presence of fire.

How to build:

First of all read the given manual thoroughly and study the circuit given in the figure. Also have look at PCB and components supplied along with the kit. Each component has to be soldered in its position on PCB.

Identification of resistors is done by color coding. The color band on each resistor corresponds to its exact value.

There are different methods in which values are defined on capacitors. But usually values are specified numerically on them.

Can you make out the whole working of circuit and are you able to identify each component separately as to where each of them has to be placed

If yes only then proceed further to actually mounting and soldering the parts.

Not ICs but their sockets are to be soldered on PCB. This is to make mounting and dismounting of ICs easy while troubleshooting.

Start from left most corner of PCB and solder the components one by one on their correct position on PCB.

Before soldering any component see that you have placed it at its right position and with correct polarity. Give due attention to diodes and electrolytic capacitors as they are polarity dependent.

Do the soldering of other components in the same way while keeping in mind that components with long and sensitive leads like capacitors and transistors are soldered last.

Testing the kit:

After assembling and soldering of components on PCB, connect external DC power source of 5V.

For testing purpose manually hold fire over flame sensor. LED glows in this case.

Now set the desired intensity at which you want detection of fire. This can be done by changing the resistive value of R2 variable resistor.

Install the unit at ceiling of room.

ICs used here:

The only IC used here is LM393

It is dual differential comparator IC.

This 8 pin IC is popular and commonly used IC

Part List:

Semiconductors

U1  – LM393

Base  – 8 pin

Resistors(all watt +/-5% carbon unless stated otherwise)

R2   – 10k Ohm(variable)

R3  – 1k Ohm

R4   – 1k Ohm

R5  – 10k Ohm

R6  – 10k Ohm

Capacitor

C1 – 1uF

Miscellaneous

D4:  – Flame Sensor

D1   – Red LED

D2:  – Green LED

5 V USB Cable

PCB

Key Applications: Used widely in electronic circuits, automation, robotics, and educational projects. Optimized for reliable performance in India-specific environments and conditions.

Keywords: Fire Indication System DIY Experiments Science STEM KIT (Assembled), 100% Tested, electronic components India, Fire Indication System DIY Experiments Science STEM KIT (Assembled), 100% Tested buy online, electronic supplies India, Fire Indication System DIY Experiments Science STEM KIT (Assembled), 100% Tested price.

Applications: Suitable for electronics projects, automation, and educational purposes. Widely used in Indian and international markets.

Keywords: Fire Indication System DIY Experiments Science STEM KIT (Assembled), 100% Tested, buy Fire Indication System DIY Experiments Science STEM KIT (Assembled), 100% Tested online, electronics components, Fire Indication System DIY Experiments Science STEM KIT (Assembled), 100% Tested features, Fire Indication System DIY Experiments Science STEM KIT (Assembled), 100% Tested applications, high quality Fire Indication System DIY Experiments Science STEM KIT (Assembled), 100% Tested