4 Channel Logic Level Converter
Original price was: ₹60.00.₹52.00Current price is: ₹52.00. + GST
Sold out!
- This Level Converter- 4 Channel features four high speed bi-directional 4 channels, allowing for safe and easy communication between devices operating at different logic levels.
- It can convert signals as low as 1.8 V to as high as 5 V and vice versa, and its four channels are enough to support most common bidirectional and unidirectional digital interfaces, including I²C, SPI, and asynchronous TTL serial.
- A bi-directional Level Converter- 4 Channel is a small device that safely steps down 5 Volt signals to 3.3 Volt AND steps up 3.3 Volt to 5 Volt at the same time. This level converter also works with 2.8 Volt and 1.8 Volt devices.
You must be logged in to post a review.
Related products
-
DHT11 Module Temperature and Humidity sensor Module for boards compatible with Arduino, ARM and other MCU
Original price was: ₹120.00.₹65.00Current price is: ₹65.00. + GSTAdd to cartThe DHT11 is a commonly used Temperature and humidity sensor. The sensor comes with a dedicated NTC to measure temperature and an 8-bit microcontroller to output the values of temperature and humidity as serial data. The sensor is also factory calibrated and hence easy to interface with other microcontrollers.
-
Quartz Crystal Oscillator 16MHz HC-49S 2 Pin for TV, car Electronics, PC Card, Electronic Watch, DVD, MP3v
Original price was: ₹15.00.₹6.72Current price is: ₹6.72. + GSTAdd to cartCrystal Oscillators are used as a quick and easy way to offer circuits a very accurate and consistent frequency output. This 16 MHz Crystal is a thru-hole type and is typically used with microcontrollers. -
8 Channel 5V Relay Board Expansion Module Optocoupler compatible UNO Raspberry
Original price was: ₹312.00.₹246.16Current price is: ₹246.16. + GSTAdd to cartSpecification
- This relay module is 5 Volts active low.
- It is an 8-channel relay interface board, which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, PLC, etc.
- It is also able to control various appliances and other equipments with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Standard interface can be directly connected with microcontrollers.
- Red working status indicator lights are conducive to the safe use.
- Widely used for all MCU control, industrial sector, PLC control, smart home control.
- Input port IN1, IN2, IN3, IN4, IN5, IN6, IN7, IN8 low signal level effectively.
- VCC, GND : Input power.
- JD – VCC : Relay power input port,relay can power alone.
- Working voltage : 5V
- Module weight : about 112g
- package weight : about 150g
- module size : about 1.7cm X 5.5cm X 13.7cm(height * width * long)
-
7476 Dual Master-Slave J-K Flip-Flop
Original price was: ₹90.00.₹61.50Current price is: ₹61.50. + GSTAdd to cart- Supply Voltage : 7V
- Input Voltage : 5.5V
- Operating Free Air Temperature Range : 0C to +70C
- Storage Temperature Range : 65C to +150C
-
BC557 PNP General Purpose Transistor 45V 100mA TO-92 Package
Original price was: ₹5.00.₹1.17Current price is: ₹1.17. + GSTAdd to cartBC557 is a widely used PNP bipolar junction transistor manufactured in small TO-92 package. It is a general purpose PNP transistor that can be used as a switch or amplifier in electronic circuits. Its HFE ratings are 125 to 800 which makes it an ideal transistor to use as a small signal amplifier in electronic circuits for example for audio signal amplification or other, the HFE ratings of BC557 can be determined by the last letter after its number for example BC557A HFE ratings are 110-220, BC557B HFE ratings are 200-450 and BC557C HFE ratings are 420-800. The max collector dissipation is 500 milliwatt which is also an another good point to use it in amplification stages. Moreover it will also perform well when used it as a switch for load under 100mA. The transistor has also good collector to emitter (VCE) value that is -45V, therefore you can easily use it in circuits using 40 to 45 volts DC.
Reviews
There are no reviews yet.