“1N4148 Zener Diode” has been added to your cart. View cart
BT136 600D triac logic sensitive gate 600v 4a to220ab
₹10.00 Original price was: ₹10.00.₹7.00Current price is: ₹7.00. + GST
TSA1015Y Transistor PNP General Purpose Transistor
₹7.00 Original price was: ₹7.00.₹1.95Current price is: ₹1.95. + GST
Viper22A Low Power Off Line SMPS Primary Switcher
Rated 4.50 out of 5 based on 12 customer ratings
(12 customer reviews)
₹40.00 Original price was: ₹40.00.₹25.16Current price is: ₹25.16. + GST
Specification
- VDS(sw) Switching Drain Source Voltage (Tj=25 … 125?C) -0.3 .. 730 V
- VDS(st) Start Up Drain Source Voltage (Tj=25 … 125?C) -0.3 .. 400 V
- ID Continuous Drain Current Internally limited A
- VDD Supply Voltage 0 to 45 V
- IFB Feedback Current 3 mA
- Tc Case Operating Temperature -40 to 150 ?C
- Tstg Storage Temperature -55 to 150 ?C
34 in stock
SKU:
B-2
Categories: Electronic, Power Supply
Description
Viper22A is a high voltage IC, intended to be used in off line power supply switching with advantage of having low part count and small size.
The?Viper22A IC?combines a dedicated current mode?PWM controller?with a high voltage?Power MOSFET?on the same silicon chip. Typical applications cover off line power supplies for battery charger adapters, standby power supplies for TV or monitors, auxiliary supplies for motor control, etc.
The internal control circuit offers the following benefits:
- Large input voltage range on the VDD pin accommodates changes in auxiliary supply voltage. This feature is well adapted to battery charger adapter configurations.
- Automatic burst mode in low load condition.
- Over voltage protection in hiccup mode.
Reviews (12)
12 reviews for Viper22A Low Power Off Line SMPS Primary Switcher
Add a review Cancel reply
You must be logged in to post a review.
Shipping and Delivery
We deliver all across India.
✅ Orders leave warehouse in 1–2 days.
✅ Delivery within 5–10 days after dispatch.
Related products
5V Single Channel Relay Module
Rated 4.17 out of 5
Relays are output devices which are used to control or operate some external devices. This is a 5 volt Isolated relay module which means that there is a optocoupler used in between your control circuit and the relay thus protecting your circuit in case of any short circuit issues on the relay side. Perfect for use in various electronics projects in India, Single Channel 5v Relay Module High Low Level Trigger ensures reliability and performance. Ideal for various electronics projects, Single Channel 5v Relay Module High Low Level Trigger offers quality and performance.
BC557 PNP General Purpose Transistor 45V 100mA TO-92 Package
Rated 5.00 out of 5
BC557 is a widely used PNP bipolar junction transistor manufactured in small TO-92 package. It is a general purpose PNP transistor that can be used as a switch or amplifier in electronic circuits. Its HFE ratings are 125 to 800 which makes it an ideal transistor to use as a small signal amplifier in electronic circuits for example for audio signal amplification or other, the HFE ratings of BC557 can be determined by the last letter after its number for example BC557A HFE ratings are 110-220, BC557B HFE ratings are 200-450 and BC557C HFE ratings are 420-800. The max collector dissipation is 500 milliwatt which is also an another good point to use it in amplification stages. Moreover it will also perform well when used it as a switch for load under 100mA. The transistor has also good collector to emitter (VCE) value that is -45V, therefore you can easily use it in circuits using 40 to 45 volts DC.
2N2222 – 40V General Purpose Transistor – NPN – TO-92
Rated 4.48 out of 5
L298N Motor Driver Controller Board
Rated 5.00 out of 5
It can control upto 4 DC motors, or 2 DC motors with directional and speed control. It can drive motors upto 46V with a total DC current of up to 4A. You can connect the two channels in parallel to double the maximum current or in series to double the maximum input voltage. Perfect for use in various electronics projects in India, L298N Motor Driver Controller Board Module | Dual H-Bridge DC Stepper Driver for Arduino | NodeMCU | Raspberry Pi Development Board - ensures reliability and performance. Ideal for various electronics projects, L298N Motor Driver Controller Board Module | Dual H-Bridge DC Stepper Driver for Arduino | NodeMCU | Raspberry Pi Development Board - offers quality and performance.
Green 10mm LED
Rated 4.50 out of 5
This is10mm Green LED. The size refers to the outside diameter of the LED, with 5mm being the most common LED model. 3mm LEDs are the smallest and used in tight-fitting applications. 8mm and 10mm models are used to output as much light as possible. Perfect for use in various electronics projects in India, Green 10mm LED ensures reliability and performance. Ideal for various electronics projects, Green 10mm LED offers quality and performance.
74HC595 8-bit Shift Register IC
Rated 4.62 out of 5
The 74HC595 consists of an 8?bit shift register and an 8?bit D?typelatch with three?state parallel outputs. The shift register accepts serialdata and provides a serial output. The shift register also providesparallel data to the 8?bit latch. The shift register and latch haveindependent clock inputs. This device also has an asynchronous resetfor the shift register.The HC595 directly interfaces with the SPI serial data port onCMOS MPUs and MCUs
Crystal Oscillator 8 MHZ
Rated 4.00 out of 5
This is a 8MHZ Crystal. This is a low cost crystal oscillator with?oscillation frequency of 8Mhz. Crystal are normally required to provide?clock pulses to your micro controller or other IC's which require external clock?source.
An oscillator crystal has two electrically conductive plates, with a slice or?tuning fork of quartz crystal sandwiched between them. The crystal oscillator?circuit sustains oscillation by taking a voltage signal from the quartz?resonator, amplifying it, and feeding it back to the resonator. Quartz has the?further advantage that its elastic constants and its size change in such a way?that the frequency dependence on temperature can be very low.
Voltage Sensor Module
Rated 4.42 out of 5
This DC Voltage Sensor Module is essentially a 5:1 potential divider circuit built using precession resistors for high accuracy.
The Arduino analog input is limited to a 5 VDC input. If you wish to measure higher voltages,this module allows you to measure voltages of 0-25V. Keep in mind, you are restricted to voltages that are less than 25 volts. More than that and you will exceed the voltage limit of your Arduino input. Perfect for use in various electronics projects in India, Voltage Sensor Module 25V ensures reliability and performance. Ideal for various electronics projects, Voltage Sensor Module 25V offers quality and performance.


















Shubham (verified owner) –
Less cost than other websites
Ketan (verified owner) –
I got my project done with these components Great Support
Komal (verified owner) –
Good service.
Shubham (verified owner) –
Less cost than other websites
Prakash (verified owner) –
The product is firmly packed.
Rahul (verified owner) –
Very well worth the money.
Devendra (verified owner) –
I got my project done with these components Great Support
Vikas (verified owner) –
Good quality.
Rohit (verified owner) –
I got my project done with these components Great Support
Ayush (verified owner) –
Good service.
Prakash (verified owner) –
Very well worth the money.
Ketan (verified owner) –
Good techinical knowledge