TL431 Adjustable Precision Shunt Regulator TO-92 Package
Original price was: ₹7.00.₹2.34Current price is: ₹2.34. + GST
145 in stock
TL431 is three-terminal adjustable regulator series with a guaranteed thermal stability over applicable temperature ranges. The output voltage may be set to any value between VREF (approximately 2.5 volts) and 36 volts with two external resistors. These devices have a typical dynamic output impedance of 0.2?. Active output circuitry provides a very sharp turn-on characteristic, making these devices excel lent replacement for zener diodes in many applications.
Features:-
- Programmable Output Voltage to 36 Volts
- Low Dynamic Output Impedance 0.2? Typical
- Sink Current Capability of 1.0 to 100mA
- Equivalent Full-Range Temperature Coefficient of 50ppm/?C Typical
- Temperature Compensated For Operation Over Full Rated Operating Temperature Range
- Low Output Noise Voltage
- Fast Turn-on Response
You must be logged in to post a review.
Related products
-
Optocoupler High Level Relay Module Board 5V 4-CH for PIC ARM DSP AVR | Compatible with Arduno NodeMCU Raspberry Pi | Pack of 1 | Blue (Excellent Quality)
Original price was: ₹139.00.₹136.50Current price is: ₹136.50. + GSTAdd to cartSpecification
- Size : 75mm (length) x 55mm (W) x 19.3mm (height);
- Weight : 80g;
- PCB Color : Blue;
- board four weeks with four screw holes, hole diameter 3.1mm, easy to install and fixed;
- Relay selection of quality loose music relays, SPDT. A common terminal, a normally open, one normally closed terminal;
- optocoupler isolation, good anti-jamming;
- Low pull, high release. Energisation status indicator light, release status LED is off;
- VCC for the system power, JD_VCC for the relay power. Default hair 12V relay, plug the jumper cap to;
- Relay Maximum output : DC 30V/10A, AC 250V/10A
- Wiring : VCC : positive power supply system GND : System power supply negative IN1 ? IN4 : relay control ports
-
BC547 NPN General Purpose Transistor
Original price was: ₹5.00.₹0.98Current price is: ₹0.98. + GSTAdd to cartBC547 is a general purpose BJT NPN transistor mostly used in electronics hobbyists and educational electronics projects. Besides these uses it can also be used in commercial circuits. It comes in TO-92 packaging and the maximum output current this transistor can handle is 100mA. The transistor is having very good DC current gain and low noise capabilities due to which it is ideal to use in signal amplification stages. The typical saturation voltage is only 90 millivolts which is also a good sign to use it as a switch.
-
5V Low Level Solid State Relay Module with Fuse SSR 250V 2A Fuse
Original price was: ₹150.00.₹110.00Current price is: ₹110.00. + GSTAdd to cart1-Channel?Solid-State Relay is some what similar to that of a mechanical relay & the difference is that, there is no moving contact in a Solid-State Relay. Here we make use of Phototropic coupler to turn it ON and OFF.
-
DHT11 Module Temperature and Humidity sensor Module for boards compatible with Arduino, ARM and other MCU
Original price was: ₹120.00.₹65.00Current price is: ₹65.00. + GSTAdd to cartThe DHT11 is a commonly used Temperature and humidity sensor. The sensor comes with a dedicated NTC to measure temperature and an 8-bit microcontroller to output the values of temperature and humidity as serial data. The sensor is also factory calibrated and hence easy to interface with other microcontrollers.
-
Voltage Sensor Module 25VDC
Original price was: ₹16.00.₹15.08Current price is: ₹15.08. + GSTAdd to cartThis DC Voltage Sensor Module is essentially a 5:1 potential divider circuit built using precession resistors for high accuracy.
The Arduino analog input is limited to a 5 VDC input.? If you wish to measure higher voltages,this module allows you to measure voltages of 0-25V. Keep in mind, you are restricted to voltages that are less than 25 volts. More than that and you will exceed the voltage limit of your Arduino input.
Reviews
There are no reviews yet.