Get Flat 5% Use code- *FLAT5* and Free delivery on orders above Rs 900 | * Single Delivery charges for Multiple Items *

Cart

Your Cart is Empty

Back To Shop

Cart

Your Cart is Empty

Back To Shop

Category: Motor Drivers

Motor Drivers

Showing all 6 results

  • A4988 driver Stepper Motor Driver

    75.44 + GST

    The A4988 driver Stepper Motor Driver is a complete micro-stepping motor driver with built-in converter, easy to operate. It operates from 8?V to 35?V and can deliver up to approximately 1?A per phase without a heat sink or forced air flow (it is rated for 2?A per coil with sufficient additional cooling).

    Purchase & earn 75 SmartX Rewards Coin!Add to cartBuy now
  • DRV8825 Stepper Motor Driver with Aluminum Heat Sink

    121.00 + GST

    Specification

    Input Supply Voltage (VDC)8.2 ~ 42
    Current Handling Capacity (A)2.2
    Continuous Current (A)1.5 (per phase)
    Logic Input (V)2.5 ~ 5
    Length (mm)15
    Width (mm)20
    Weight (gm)4
    Shipment Weight0.005 kg
    Shipment Dimensions4 ? 4 ? 4 cm
    Purchase & earn 121 SmartX Rewards Coin!Add to cartBuy now
  • Specification

    • Supplied Fully Assembled
    • 2x 5V Servo outputs connected to the high-resolution dedicated timer – no jitter!
    • Can drive 4 DC motors or 2 stepper motors or 2 Servo’s
    • Up to 4 bi-directional DC motors with individual 8-bit speed selection
    • Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.
    • 4 H-Bridges: per bridge provides 0.6A (1.2A peak current) with thermal protection, can run motors on 4.5V to 36V DC
    • Pull down resistors keep motors disabled during power-up
    • reset button
    • Tested compatible for Arduino Mega, Diecimila, Duemilanove, Arduino UNO
    Purchase & earn 157 SmartX Rewards Coin!Add to cartBuy now
  • MDD10A Dual Channel Enhanced 10Amp DC Motor Driver 30A Peak

    1,949.71 + GST

    Specification

    Arduino SheildNo- can be used with Wire connection
    Operating ModesPWM (Lock-Antiphase and Sign-Magnitude): Yes, UART: No, Analog:No, RC Servo Signal: No
    Continuous Current (A)10
    Cooling FanNo
    Driver ModelMDD10A
    LED IndicatorYes
    No. of Channels2
    Operating Voltage (VDC)5 ~ 25
    Peak Current (A)30
    Polarity ProtectionNO
    Dimensions in mm (LxWxH)85 x 62 x 25
    Weight (gm)40
    OthersNo heat sink is required
    Shipment Weight0.043 kg
    Shipment Dimensions7 ? 5 ? 3 cm
    Purchase & earn 1,950 SmartX Rewards Coin!Add to cartBuy now
  • Specification

    Operating Voltage rangeDC6V ? 28V
    Operating Current RangeWithin 3A
    Speed range0-100%
    Length (mm)65
    Width (mm)32
    Height (mm)15
    Weight (gm)25
    Shipment Weight0.03 kg
    Shipment Dimensions6 ? 5 ? 3 cm

    _x000D_

    Purchase & earn 138 SmartX Rewards Coin!Add to cartBuy now
  • ULN2003 Uln2003 5V Stepper Motor + Uln2003 Driver Board for Arduino

    149.50 + GST

    This 5V DC 28BYJ-48 Stepper Motor is small, inexpensive and high-quality geared step motor. The?28BYJ-48 Stepper Motor and ULN2003 Stepper Motor Driver is a widely popular combination of the stepper motor and stepper driver, because of the stability and reliability of the system.

    Purchase & earn 150 SmartX Rewards Coin!Add to cartBuy now

Cart

Your Cart is Empty

Back To Shop
GET DISCOUNT CODE

It will take just few seconds to claim 7% Discount

    X
    GET DISCOUNT CODE