NE5534P NE5534 5534 DIP-8 TI Low-Noise Operational Amplifier IC
₹23.40 + GST
50 in stock
Specification
- Slew Rate – 13v/ us
- Gain Bandwidth product – 10mhz
- Current Input Biase -500nA
- Voltage Input Offset -? 500 uv
- Current Supply -4 mA
- Current Output -38mA
- Voltage Supply Span (min ) -10v
- Voltage Supply Span ( max ) -30v
12 reviews for NE5534P NE5534 5534 DIP-8 TI Low-Noise Operational Amplifier IC
You must be logged in to post a review.
Related products
- Add to cart
2N2222 is NPN BJT?normally used in low power amplifiers and also for switching application.
2n2222 is used as a?small signal transistor?and used as a general purpose transistor and is very popular. ?This is in TO-92 package form.
- Add to cart
- Decade counter/decimal decode display (CD4017B)
- Binary counter/decoder
- Frequency division
- Counter control/timers
- Divde-by-N counting
- For further application information, see ICAN-6166 “COS/MOS MSI Counter and Register Design and Applications”
- Add to cart
Specification
- Size : 75mm (length) x 55mm (W) x 19.3mm (height);
- Weight : 80g;
- PCB Color : Blue;
- board four weeks with four screw holes, hole diameter 3.1mm, easy to install and fixed;
- Relay selection of quality loose music relays, SPDT. A common terminal, a normally open, one normally closed terminal;
- optocoupler isolation, good anti-jamming;
- Low pull, high release. Energisation status indicator light, release status LED is off;
- VCC for the system power, JD_VCC for the relay power. Default hair 12V relay, plug the jumper cap to;
- Relay Maximum output : DC 30V/10A, AC 250V/10A
- Wiring : VCC : positive power supply system GND : System power supply negative IN1 ? IN4 : relay control ports
DHT11 Module Temperature and Humidity sensor Module for boards compatible with Arduino, ARM and other MCU
₹88.05 + GSTAdd to cartThe DHT11 is a commonly used Temperature and humidity sensor. The sensor comes with a dedicated NTC to measure temperature and an 8-bit microcontroller to output the values of temperature and humidity as serial data. The sensor is also factory calibrated and hence easy to interface with other microcontrollers.
- Add to cart
BC557 is a widely used PNP bipolar junction transistor manufactured in small TO-92 package. It is a general purpose PNP transistor that can be used as a switch or amplifier in electronic circuits. Its HFE ratings are 125 to 800 which makes it an ideal transistor to use as a small signal amplifier in electronic circuits for example for audio signal amplification or other, the HFE ratings of BC557 can be determined by the last letter after its number for example BC557A HFE ratings are 110-220, BC557B HFE ratings are 200-450 and BC557C HFE ratings are 420-800. The max collector dissipation is 500 milliwatt which is also an another good point to use it in amplification stages. Moreover it will also perform well when used it as a switch for load under 100mA. The transistor has also good collector to emitter (VCE) value that is -45V, therefore you can easily use it in circuits using 40 to 45 volts DC.
Ayush (verified owner) –
Very fast delivery.
Prakash (verified owner) –
Very fast delivery.
Akshay (verified owner) –
Good service.
Er.Prashant (verified owner) –
I got my project done with these components Great Support
Vivek (verified owner) –
I got my project done with these components Great Support
Priya (verified owner) –
Less cost than other websites
Roma (verified owner) –
Good techinical knowledge
Vivek (verified owner) –
Good techinical knowledge
Jayen (verified owner) –
Best cost electronic components in India
Zohar (verified owner) –
Very fast delivery.
Ketan (verified owner) –
The product is firmly packed.
Mayur (verified owner) –
Online best cost electronic components