Flame Sensor Infrared Receiver Module Ignition Source Detection Module
₹51.57 + GST
Specification:
- Can detect a flame or in a 760 nanometer wavelength of ~ 1100 nm range of the light, lighter flame test distance of 80cm, for the greater flame, the farther the distance test
- The detection angle of 60 degrees or so, particularly sensitive to the flame spectrum
- Sensitivity adjustable (shown in blue digital potentiometer adjustment)
- The comparator output signal clean, good waveform, driving ability, more than 15mA
- With adjustable precision potentiometer sensitivity adjustment
- The working voltage of 3.3V-5V
- The output format : DO digital switching outputs (0 and 1) and AO analog voltage output
- A fixed bolt holes for easy installation
- Using a wide voltage LM393 comparator
15 in stock
- Responses to a detected flame depend on the installation, but can include sounding an alarm, deactivating a fuel line (such as a propane or a natural gas line), and activating a fire suppression system. When used in applications such as industrial furnaces, their role is to provide confirmation that the furnace is properly lit; in these cases they take no direct action beyond notifying the operator or control system. A flame detector can often respond faster and more accurately than a smoke or heat detector due to the mechanisms it uses to detect the flame.
- A flame detector is a sensor designed to detect and respond to the presence of a flame or fire.
1 review for Flame Sensor Infrared Receiver Module Ignition Source Detection Module
You must be logged in to post a review.
Related products
- Add to cart
BC557 is a widely used PNP bipolar junction transistor manufactured in small TO-92 package. It is a general purpose PNP transistor that can be used as a switch or amplifier in electronic circuits. Its HFE ratings are 125 to 800 which makes it an ideal transistor to use as a small signal amplifier in electronic circuits for example for audio signal amplification or other, the HFE ratings of BC557 can be determined by the last letter after its number for example BC557A HFE ratings are 110-220, BC557B HFE ratings are 200-450 and BC557C HFE ratings are 420-800. The max collector dissipation is 500 milliwatt which is also an another good point to use it in amplification stages. Moreover it will also perform well when used it as a switch for load under 100mA. The transistor has also good collector to emitter (VCE) value that is -45V, therefore you can easily use it in circuits using 40 to 45 volts DC.
BC327 PNP General Purpose Amplifier Transistor
₹1.92 + GSTAdd to cartBC327 is a general purpose PNP BJP transistor that can be used for switching and amplification purposes in electronic circuits. The transistor features 800mA collector current hence it can be used to drive variety of loads in an electronic application. The max collector-emitter voltage is -45V therefore it can easily handle load voltage under 45V. Apart from that transistor also features 625mW collector dissipation and DC current gain of maximum 630 therefore it can also be used as an audio amplifier or for any type of signal amplification.
- Add to cart
1N4007 is an axial leaded general purpose rectifier in DO-41 package. This device features epoxy flame retardant, low forward voltage drop and high current capability and high reliability.
BC548 NPN 30V 0. 1A Transistor High quality
₹1.23 + GSTAdd to cartBC548 is another general purpose widely used transistor that can be easily get from reputable electronic components store, this transistor also have bunch of good features on the basis of which one can use it in their electronic circuit, it can handle maximum current of 500mA which is enough to drive many other components such as ICS, other transistors, portion of a circuits, relays, LEDs etc. The max collector dissipation of the device is 625 miliWatt which is another good feature to use it as a small amplifier.
- Add to cart
Relays are output devices which are used to control or operate some external devices.? This is a 5 volt Isolated relay module which means that there is a optocoupler used in between your control circuit and the relay thus protecting your circuit in case of any short circuit issues on the relay side.
Harsh (verified owner) –
Good support and recommended