Female to Female/breadboard jumper wires
Original price was: ₹2.42.₹2.02Current price is: ₹2.02. + GST
This cable is an electrical wire or group of them in a cable with a connector or pins at each end, which is normally for interconnecting the components of a breadboard or other prototype or test circuit, internally or with other equipment or components, without soldering.
Sold out!
- Random color
- Length: 200mm
- Weight: 25 gm
- Compatible with 2.54mm spacing pin headers
- 1 pcs chromatic female to female color jump wire
- High quality and in good working condition
- Durable and reusable
- Easy to install and use
You must be logged in to post a review.
Related products
-
Lcd 16X2 Yellow Backlight Alphanumeric Display for 8051,Avr,Arduino,Raspberry Pi,Pic,Arm All Microcontroller (Green)
Original price was: ₹112.00.₹91.82Current price is: ₹91.82. + GSTAdd to cart- Operating Voltage is 4.7V to 5.3V
- Current consumption is 1mA without backlight
- Alphanumeric LCD display module, meaning can display alphabets and numbers
- Consists of two rows and each row can print 16 characters.
- Each character is build by a 5?8 pixel box
- Can work on both 8-bit and 4-bit mode
- It can also display any custom generated characters
- Available in Green Backlight
-
8 Channel 5V Relay Board Expansion Module Optocoupler compatible UNO Raspberry
Original price was: ₹312.00.₹246.16Current price is: ₹246.16. + GSTAdd to cartSpecification
- This relay module is 5 Volts active low.
- It is an 8-channel relay interface board, which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, PLC, etc.
- It is also able to control various appliances and other equipments with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Standard interface can be directly connected with microcontrollers.
- Red working status indicator lights are conducive to the safe use.
- Widely used for all MCU control, industrial sector, PLC control, smart home control.
- Input port IN1, IN2, IN3, IN4, IN5, IN6, IN7, IN8 low signal level effectively.
- VCC, GND : Input power.
- JD – VCC : Relay power input port,relay can power alone.
- Working voltage : 5V
- Module weight : about 112g
- package weight : about 150g
- module size : about 1.7cm X 5.5cm X 13.7cm(height * width * long)
-
BC548 NPN 30V 0. 1A Transistor High quality
Original price was: ₹5.00.₹1.17Current price is: ₹1.17. + GSTAdd to cartBC548 is another general purpose widely used transistor that can be easily get from reputable electronic components store, this transistor also have bunch of good features on the basis of which one can use it in their electronic circuit, it can handle maximum current of 500mA which is enough to drive many other components such as ICS, other transistors, portion of a circuits, relays, LEDs etc. The max collector dissipation of the device is 625 miliWatt which is another good feature to use it as a small amplifier.
-
Original Flex sensor 2.2 inches for Motion and Diy
Original price was: ₹400.00.₹240.50Current price is: ₹240.50. + GSTAdd to cartFlex sensors are usually available in two sizes. One is 2.2 inch and another is 4.5 inch. Although the sizes are different the basic function remains the same. They are also divided based on resistance. There are LOW resistance, MEDIUM resistance and HIGH resistance types. Choose the appropriate type depending on requirement. ?Here we are going to discuss 2.2inch Flex sensor that is FS-L-0055.
-
Voltage Sensor Module 25VDC
Original price was: ₹16.00.₹15.08Current price is: ₹15.08. + GSTAdd to cartThis DC Voltage Sensor Module is essentially a 5:1 potential divider circuit built using precession resistors for high accuracy.
The Arduino analog input is limited to a 5 VDC input.? If you wish to measure higher voltages,this module allows you to measure voltages of 0-25V. Keep in mind, you are restricted to voltages that are less than 25 volts. More than that and you will exceed the voltage limit of your Arduino input.
Reviews
There are no reviews yet.