7x7mm 6 Pin DPDT Self-Lock lock Push Switch
₹5.20 + GST
The mini push button 6 pin switch is useful in controlling power connections most of the time. The blue coloured square push button is DIP through-hole for mounting on PCB.
149 in stock
- Switch type: Non-Momentary
- Small? 7 x 7 mm. Size
- PCB through-hole mounting
- Maximum voltage DC30V
- Operating Current 0.1 A
12 reviews for 7x7mm 6 Pin DPDT Self-Lock lock Push Switch
You must be logged in to post a review.
Related products
Quartz Crystal Oscillator 16MHz HC-49S 2 Pin for TV, car Electronics, PC Card, Electronic Watch, DVD, MP3v
₹6.72 + GSTAdd to cartCrystal Oscillators are used as a quick and easy way to offer circuits a very accurate and consistent frequency output. This 16 MHz Crystal is a thru-hole type and is typically used with microcontrollers.DHT11 Module Temperature and Humidity sensor Module for boards compatible with Arduino, ARM and other MCU
₹88.05 + GSTAdd to cartThe DHT11 is a commonly used Temperature and humidity sensor. The sensor comes with a dedicated NTC to measure temperature and an 8-bit microcontroller to output the values of temperature and humidity as serial data. The sensor is also factory calibrated and hence easy to interface with other microcontrollers.
Original Flex sensor 2.2 inches for Motion and Diy
₹276.73 + GSTAdd to cartFlex sensors are usually available in two sizes. One is 2.2 inch and another is 4.5 inch. Although the sizes are different the basic function remains the same. They are also divided based on resistance. There are LOW resistance, MEDIUM resistance and HIGH resistance types. Choose the appropriate type depending on requirement. ?Here we are going to discuss 2.2inch Flex sensor that is FS-L-0055.
Voltage Sensor Module 25VDC
₹50.12 + GSTAdd to cartThis DC Voltage Sensor Module is essentially a 5:1 potential divider circuit built using precession resistors for high accuracy.
The Arduino analog input is limited to a 5 VDC input.? If you wish to measure higher voltages,this module allows you to measure voltages of 0-25V. Keep in mind, you are restricted to voltages that are less than 25 volts. More than that and you will exceed the voltage limit of your Arduino input.
- Add to cart
Specification
- This relay module is 5 Volts active low.
- It is an 8-channel relay interface board, which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, PLC, etc.
- It is also able to control various appliances and other equipments with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Standard interface can be directly connected with microcontrollers.
- Red working status indicator lights are conducive to the safe use.
- Widely used for all MCU control, industrial sector, PLC control, smart home control.
- Input port IN1, IN2, IN3, IN4, IN5, IN6, IN7, IN8 low signal level effectively.
- VCC, GND : Input power.
- JD – VCC : Relay power input port,relay can power alone.
- Working voltage : 5V
- Module weight : about 112g
- package weight : about 150g
- module size : about 1.7cm X 5.5cm X 13.7cm(height * width * long)
Rahul (verified owner) –
Less cost than other websites
Harsh (verified owner) –
Online best cost electronic components
Roma (verified owner) –
I got my project done with these components Great Support
Prakash (verified owner) –
Best cost electronic components in India
Devendra (verified owner) –
Drone parts i ordered and found ok
Prakash (verified owner) –
Very well worth the money.
Paaji (verified owner) –
Good techinical knowledge
Akshay (verified owner) –
The product is firmly packed.
Shubham (verified owner) –
I got my project done with these components Great Support
Er.Prashant (verified owner) –
Good techinical knowledge
Shubham (verified owner) –
Very well worth the money.
Priya (verified owner) –
Online best cost electronic components