1M Mega Ohm Carbon Film Resistor 1/4 W Resistance 0.25 Watt 250mW 5% Toleance High Quality For DIY
₹0.82 + GST
A resistor is a passive two-terminal electrical component that implements electrical resistance as a circuit element. In electronic circuits, resistors are used to reduce current flow, adjust signal levels, to divide voltages, bias active elements, and terminate transmission lines, among other uses.
(Note: Product Images are shown for illustrative purposes only and may differ from actual product.)
959 in stock
959 in stock
A resistor is a passive two-terminal electrical component that implements electrical resistance as a circuit element. In electronic circuits, resistors are used to reduce current flow, adjust signal levels, to divide voltages, bias active elements, and terminate transmission lines, among other uses.
(Note: Product Images are shown for illustrative purposes only and may differ from actual product.)
12 reviews for 1M Mega Ohm Carbon Film Resistor 1/4 W Resistance 0.25 Watt 250mW 5% Toleance High Quality For DIY
You must be logged in to post a review.
Related products
16 x 2 (JHD162A) Blue/White color DC 5V Character LCD display module FOR ALL TYPE OF DEVLOMENT BOARD
₹96.76 + GSTAdd to cart- Operating Voltage is 4.7V to 5.3V
- Current consumption is 1mA without backlight
- Alphanumeric LCD display module, meaning can display alphabets and numbers
- Consists of two rows and each row can print 16 characters.
- Each character is build by a 5?8 pixel box
- Can work on both 8-bit and 4-bit mode
- It can also display any custom generated characters
- Available in Blue Backlight
- Add to cart
Specification
- This relay module is 5 Volts active low.
- It is an 8-channel relay interface board, which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, PLC, etc.
- It is also able to control various appliances and other equipments with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Standard interface can be directly connected with microcontrollers.
- Red working status indicator lights are conducive to the safe use.
- Widely used for all MCU control, industrial sector, PLC control, smart home control.
- Input port IN1, IN2, IN3, IN4, IN5, IN6, IN7, IN8 low signal level effectively.
- VCC, GND : Input power.
- JD – VCC : Relay power input port,relay can power alone.
- Working voltage : 5V
- Module weight : about 112g
- package weight : about 150g
- module size : about 1.7cm X 5.5cm X 13.7cm(height * width * long)
BC548 NPN 30V 0. 1A Transistor High quality
₹1.23 + GSTAdd to cartBC548 is another general purpose widely used transistor that can be easily get from reputable electronic components store, this transistor also have bunch of good features on the basis of which one can use it in their electronic circuit, it can handle maximum current of 500mA which is enough to drive many other components such as ICS, other transistors, portion of a circuits, relays, LEDs etc. The max collector dissipation of the device is 625 miliWatt which is another good feature to use it as a small amplifier.
Original Flex sensor 2.2 inches for Motion and Diy
₹276.73 + GSTAdd to cartFlex sensors are usually available in two sizes. One is 2.2 inch and another is 4.5 inch. Although the sizes are different the basic function remains the same. They are also divided based on resistance. There are LOW resistance, MEDIUM resistance and HIGH resistance types. Choose the appropriate type depending on requirement. ?Here we are going to discuss 2.2inch Flex sensor that is FS-L-0055.
- Add to cart
Specification
- Size : 75mm (length) x 55mm (W) x 19.3mm (height);
- Weight : 80g;
- PCB Color : Blue;
- board four weeks with four screw holes, hole diameter 3.1mm, easy to install and fixed;
- Relay selection of quality loose music relays, SPDT. A common terminal, a normally open, one normally closed terminal;
- optocoupler isolation, good anti-jamming;
- Low pull, high release. Energisation status indicator light, release status LED is off;
- VCC for the system power, JD_VCC for the relay power. Default hair 12V relay, plug the jumper cap to;
- Relay Maximum output : DC 30V/10A, AC 250V/10A
- Wiring : VCC : positive power supply system GND : System power supply negative IN1 ? IN4 : relay control ports
Ayush (verified owner) –
Best cost electronic components in India
Mayur (verified owner) –
Good service.
Komal (verified owner) –
Good service.
Rahul (verified owner) –
The product is firmly packed.
Vikas (verified owner) –
Less cost than other websites
Rahul (verified owner) –
The product is firmly packed.
Mayur (verified owner) –
Good support and recommended
Ayush (verified owner) –
The product is firmly packed.
Sneha (verified owner) –
Very well worth the money.
Akshay (verified owner) –
Drone parts i ordered and found ok
Devendra (verified owner) –
I got my project done with these components Great Support
Er.Prashant (verified owner) –
Good service.