5V Low Level Solid State Relay Module with Fuse SSR 250V 2A Fuse
Original price was: ₹150.00.₹110.00Current price is: ₹110.00. + GST
1-Channel?Solid-State Relay is some what similar to that of a mechanical relay & the difference is that, there is no moving contact in a Solid-State Relay. Here we make use of Phototropic coupler to turn it ON and OFF.
10 in stock
- Rated output load : 100V ~ 240V AC (50Hz/ 60Hz) 2 Ampere
- Rated input voltage : 5 Volts
- Triggered at Low level
- LED showing Solid-State Relay status
- Input control signal :
- Low Signal (Solid-State Relay ON / CLOSED)
- High Signal (Solid-State Relay OFF / OPEN)
- Screw terminals for better & secure connection
Input part:
- DC + : connected to positive power source (supply power according to the relay voltage)
- DC – : connected to negative power source
- CH1: 1- channel relay module signal triggering end (effective at high level)
1 review for 5V Low Level Solid State Relay Module with Fuse SSR 250V 2A Fuse
You must be logged in to post a review.
Related products
-
Original Flex sensor 2.2 inches for Motion and Diy
Original price was: ₹400.00.₹240.50Current price is: ₹240.50. + GSTAdd to cartFlex sensors are usually available in two sizes. One is 2.2 inch and another is 4.5 inch. Although the sizes are different the basic function remains the same. They are also divided based on resistance. There are LOW resistance, MEDIUM resistance and HIGH resistance types. Choose the appropriate type depending on requirement. ?Here we are going to discuss 2.2inch Flex sensor that is FS-L-0055.
-
Voltage Sensor Module 25VDC
Original price was: ₹16.00.₹15.08Current price is: ₹15.08. + GSTAdd to cartThis DC Voltage Sensor Module is essentially a 5:1 potential divider circuit built using precession resistors for high accuracy.
The Arduino analog input is limited to a 5 VDC input.? If you wish to measure higher voltages,this module allows you to measure voltages of 0-25V. Keep in mind, you are restricted to voltages that are less than 25 volts. More than that and you will exceed the voltage limit of your Arduino input.
-
BC548 NPN 30V 0. 1A Transistor High quality
Original price was: ₹5.00.₹1.17Current price is: ₹1.17. + GSTAdd to cartBC548 is another general purpose widely used transistor that can be easily get from reputable electronic components store, this transistor also have bunch of good features on the basis of which one can use it in their electronic circuit, it can handle maximum current of 500mA which is enough to drive many other components such as ICS, other transistors, portion of a circuits, relays, LEDs etc. The max collector dissipation of the device is 625 miliWatt which is another good feature to use it as a small amplifier.
-
BC547 NPN General Purpose Transistor
Original price was: ₹5.00.₹1.17Current price is: ₹1.17. + GSTRead moreBC547 is a general purpose BJT NPN transistor mostly used in electronics hobbyists and educational electronics projects. Besides these uses it can also be used in commercial circuits. It comes in TO-92 packaging and the maximum output current this transistor can handle is 100mA. The transistor is having very good DC current gain and low noise capabilities due to which it is ideal to use in signal amplification stages. The typical saturation voltage is only 90 millivolts which is also a good sign to use it as a switch.
-
BC327 PNP General Purpose Amplifier Transistor
Original price was: ₹5.00.₹1.95Current price is: ₹1.95. + GSTAdd to cartBC327 is a general purpose PNP BJP transistor that can be used for switching and amplification purposes in electronic circuits. The transistor features 800mA collector current hence it can be used to drive variety of loads in an electronic application. The max collector-emitter voltage is -45V therefore it can easily handle load voltage under 45V. Apart from that transistor also features 625mW collector dissipation and DC current gain of maximum 630 therefore it can also be used as an audio amplifier or for any type of signal amplification.
Lokesh (verified owner) –
Less cost than other websites