Search Results for: microcontroller
Showing 49–64 of 80 results
-
TM1637 4 Bits Digital Tube LED Display Module With Clock Display for Arduino
Original price was: ₹80.00.₹61.63Current price is: ₹61.63. + GSTAdd to cartSpecification
Driver IC TM1637 Input Voltage (V) 3.3 to 5.5 Max. Operating Current (mA) 30 Length (mm) 42 Width (mm) 24 Height (mm) 12 Weight (gm) 10 Shipment Weight 0.015 kg Shipment Dimensions 5 ? 3 ? 2 cm -
ATTINY85V2 Digispark ATTiny85 USB Development Board Digistump Mini
Original price was: ₹400.00.₹210.00Current price is: ₹210.00. + GSTAdd to cartSpecification
-
- Support for the IDE 1.0+ (OSX / Win / Linux)
- Power via USB or External Source – 5V or 7 -35V (automatic selection)
-
- On-board 500ma 5V Regulator
-
- Built-in USB(and serial debugging)
-
- 6 I/O Pins (2 are used for USB only if your program actively communicates over USB otherwise you can use all 6 even if you are programming via USB)
-
- 8k Flash Memory (about 6K after bootloader)
-
- I2C and SPI(vis USI)
-
- PWM on 3 pins (more possible with Software PWM)
-
- ADC on 4 pins
-
- Power LED and Test/ Status LED (on Pin0)
-
- Weight : 4g
-
-
4 X 4 Matrix Membrane Keypad | 4×4 Matrix Keypad Membrane Switch For Arduino, Raspberry, Arm and Other MCU | 16 key switch keypad module
Original price was: ₹60.00.₹41.87Current price is: ₹41.87. + GSTAdd to cartSpecification
-
- Ultra-thin design & adhesive backing provides easy integration to any project
-
- Excellent price-performance ratio
-
- Easy communication with any microcontroller
-
- 5 pins 2.54mm pitch connector,?4x 4type 16 keys.
-
- The sticker can peel off for adhesive mounting.
-
- Used widely in industrial and home electronic equipment, instrument, etc.
-
- This allows a microcontroller to scan? the 8 output pins to see which of the 16 buttons is being pressed.
-
-
PZIN51000043 Imported St-Link V2 Programming Unit Mini Metal Shell Stm8 Stm32 Emulator Dow
Original price was: ₹450.00.₹197.00Current price is: ₹197.00. + GSTAdd to cartST-Link V2 Programmer For STM8 and STM32 is fully consistent with the official version, support for automatic upgrades, support the full range?STM32 SWD?(only 4pins including SWCLK, SWDIO, and power)?and a full range?STM8 SWIM?(only 4pins including SWIM, Reset and power) download and debug. Use this device to send program code to the 32-bit STM32 ARM Cortex …
PZIN51000043 Imported St-Link V2 Programming Unit Mini Metal Shell Stm8 Stm32 Emulator DowRead More
-
GY-906 MLX90614ESF Module, MLX90614 Contactless Temperature Sensor Module GY-906
Original price was: ₹2,000.00.₹1,062.91Current price is: ₹1,062.91. + GSTAdd to cartSpecification
-
- Small size, low cost
-
- Mounted on a breakout board with two types of pins
-
- 10k Pull up resistors for the I2C interface with optional solder jumpers
-
- Easy to integrate
-
- Factory calibrated in wide temperature range
-
- -40 125C for sensor temperature and
-
- -70 380C for object temperature.
-
- High accuracy of 0.5C over wide temperature range
-
- (0,50 C for both Ta and To) High (medical) accuracy calibration
-
- Measurement resolution of 0.02C
-
- Single and dual zone versions
-
- SMBus compatible digital interface
-
- Customizable PWM output for continuous reading
-
- Simple adaptation for 816V applications
-
- Sleep mode for reduced power consumption
-
- Different package options for applications and measurements versatility
-
- Automotive grade
-
-
1.3 inch Blue OLED Display Module with I2C/IIC Serial Interface for boards compatible with Arduino
Original price was: ₹500.00.₹278.41Current price is: ₹278.41. + GSTRead more- This is small 1.3″ I2C interface OLED 128×64 dot matrix Display module.?This OLED Display Module is very compact and will add a great ever user interface experience to your Arduino or any Microcontroller project. The connection of this display with Arduino is made through I2C interface.
- The SH1106 1.3 Inch 128?64 OLED Display Screen Module produces blue text on black background with very good contrast when supplied with DC 3.3 Volts to 5 Volts supply. The OLED Display Modules also offers a very wide viewing angle of about greater than 160?
-
0.96″ 128 X 64 Blue Light I2C OLED Screen Display Module For DIY
Original price was: ₹211.00.₹166.36Current price is: ₹166.36. + GSTAdd to cart- The display module can be interfaced with any microcontroller using SPI/IIC protocols. It is having a resolution of 128×64. The package includes display board,display, 4 pin male header pre-soldered to board.
- OLED (Organic Light-Emitting Diode) is a self light-emitting technology composed of a thin, multi-layered organic film placed between an anode and cathode. In contrast to LCD technology, OLED does not require a backlight. OLED possesses high application potential for virtually all types of displays and is regarded as the ultimate technology for the next generation of flat-panel displays.
- OLEDs basic structure consists of organic materials positioned between the cathode and the anode, which is composed of electric conductive transparent Indium Tin Oxide (ITO). The organic materials compose a multi-layered thin film, which includes the Hole Transporting Layer (HTL), Emission Layer (EML) and the Electron Transporting Layer (ETL). By applying the appropriate electric voltage, holes and electrons are injected into the EML from the anode and the cathode, respectively. The holes and electrons combine inside the EML to form excitons, after which electro luminescence occurs. The transfer material, emission layer material and choice of electrode are the key factors that determine the quality of OLED components.
-
NRF24L01 2.4GHz Wireless Transceiver Module
Original price was: ₹100.00.₹50.02Current price is: ₹50.02. + GSTAdd to cart- Has on board antenna. The nRF24L01 is a single chip 2.4GHz transceiver with an embedded baseband protocol engine (Enhanced ShockBurst?), designed for ultra low power wireless applications.
- The nRF24L01 is designed for operation in the world wide ISM frequency band at 2.400 – 2.4835GHz. An MCU (microcontroller) and very few external passive components are needed to design a radio system with the nRF24L01. The nRF24L01 is configured and operated through a Serial Peripheral Interface (SPI.) Through this interface the register map is available. The register map contains all configuration registers in the nRF24L01 and is accessible in all operation modes of the chip.
- The embedded baseband protocol engine (Enhanced ShockBurst?) is based on packet communication and supports various modes from manual operation to advanced autonomous protocol operation. Internal FIFOs ensure a smooth data flow between the radio front end and the system?s MCU. Enhanced ShockBurst? reduces system cost by handling all the high-speed link layer operations. The radio front end uses GFSK modulation. It has user configurable parameters like frequency channel, output power and air data rate.
- DNA Solutions has large collection of various types of Transceiver Module. Check our complete collection of Transceiver Module
-
ISD1820 Voice Record Module
Original price was: ₹200.00.₹131.00Current price is: ₹131.00. + GSTAdd to cart- It can offers true single?chip voice recording, no?volatile storage, and playback capability for 8 to 20 seconds. The sample is 3.2k and the total 20s for the Recorder. This module use is very easy which you could direct control by push button on board or by Microcontroller such as Arduino, STM32, ChipKit etc. From these, you can easy control record , playback and repeat and so on.
- We have Various sizes of Audio, Sound and Voice Module. Check out our complete collection of Audio, Sound and Voice Module.
-
MAX7219 8×8 LED Dot Matrix Display Module
Original price was: ₹160.00.₹128.30Current price is: ₹128.30. + GSTAdd to carthe individual module features 8?8 LED?s, each controlled very precisely by?the MAX7219 driver to generate the color pattern you wish. The great advantage of using this is users will have control over all of the 64 LED by just connecting 3 output communication wires to microcontrollers like Arduino etc.
-
IRFZ44N MOSFET – 55V 49A N-Channel Power MOSFET TO-220 Package
Original price was: ₹30.00.₹20.12Current price is: ₹20.12. + GSTAdd to cartThe IRFZ44N is known for its high drain current and fast switching speed. Adding to that it also has a low Rds value which will help in increasing the efficiency of switching circuits. The MOSFET will start turning on with a small gate voltage of 4V, but the drain current will be maximum only when a gate voltage of 10V is applied. If the mosfet has to be driven directly from a microcontroller like Arduino then try the logic level version IRLZ44N mosfet.
-
12V Zener 0.5W voltage regulator diode
Original price was: ₹5.00.₹1.64Current price is: ₹1.64. + GSTAdd to cart- Used in Voltage protection circuits
- Can be used as low current voltage regulator
- Input voltage protection for Microcontrollers or other IC?s
- Voltage stabilizing circuits
-
zener diode 18v 0.5w
Original price was: ₹5.00.₹1.64Current price is: ₹1.64. + GSTAdd to cart- Used in Voltage protection circuits
- Can be used as low current voltage regulator
- Input voltage protection for Microcontrollers or other IC?s
- Voltage stabilizing circuits
-
24V 1/2w Zener Diode
Original price was: ₹5.00.₹1.64Current price is: ₹1.64. + GSTAdd to cart- Used in Voltage protection circuits
- Can be used as low current voltage regulator
- Input voltage protection for Microcontrollers or other IC?s
- Voltage stabilizing circuits
-
Zener Voltage Regulator Diode 4.7 Volt 0.5 Watt
Original price was: ₹2.42.₹2.02Current price is: ₹2.02. + GSTAdd to cart- Used in Voltage protection circuits
- Can be used as low current voltage regulator
- Input voltage protection for Microcontrollers or other IC?s
- Voltage stabilizing circuits
-
Nano CH340 Chip Board without USB cable compatible with Arduino
Original price was: ₹388.00.₹240.50Current price is: ₹240.50. + GSTAdd to cartArduino NANO Version 3 is the open source smallest Embedded Development board launched by Arduino based on Atmega328 SMD Package Microcontroller. It is a Surface mount Breadboard Friendly board integrated with Mini USB Port. DC Power Jack is not available on this Board, so power can be given through Mini USB Cable. It automatically sense and switch to the higher potential source of power, there is no need for the power select jumper.