UNO R3 SMD Board compatible with Arduino | Development Board
₹378.00
Arduino UNO R3 SMD is the open source Embedded Development board launched by Arduino based on Atmega328 SMD Package Microcontroller. Because Atmel is moving more and more of their production capacity to surface mount ICs, the DIP packaged ATmega is becoming more and more difficult to get.
46 in stock
46 in stock
Microcontroller : ATmega328 SMD.
Operating Voltage : 5V.
Supply Voltage recommended : 7-12V DC.
Digital I/O Pins : 14 (of which 6 provide PWM output).
Analog Input Pins : 6.
DC Current per I/O Pin : 40 mA.
DC Current for 3.3V Pin : 50 mA.
Flash Memory : 32 KB (ATmega328) of which 0.5 KB used by bootloader.
SRAM : 2 KB (ATmega328).
EEPROM : 1 KB (ATmega328).
Clock Speed : 16 MHz.
* Product Images are shown for illustrative purposes only and may differ from actual product.
12 reviews for UNO R3 SMD Board compatible with Arduino | Development Board
You must be logged in to post a review.
Related products
- Add to cartCore processor ESP8266 in smaller sizes of the module encapsulates Tensilica L106 integrates industry-leading ultra low power 32-bit MCU micro, with the 16-bit short mode, Clock speed support 80 MHz, 160 MHz, supports the RTOS, integrated Wi Fi MAC/BB/RF/PA/LNA, on-board antenna.
- Add to cart
BC547 is a general purpose BJT NPN transistor mostly used in electronics hobbyists and educational electronics projects. Besides these uses it can also be used in commercial circuits. It comes in TO-92 packaging and the maximum output current this transistor can handle is 100mA. The transistor is having very good DC current gain and low noise capabilities due to which it is ideal to use in signal amplification stages. The typical saturation voltage is only 90 millivolts which is also a good sign to use it as a switch.
- Add to cart
- Widely used in small-scale as well as prototyping projects where 12 to 30 volts power supply needed
- Supports DC Power Jack: 2.1 x 5.5 mm
- Diameter: 14mm
- Add to cart
Specification
- This relay module is 5 Volts active low.
- It is an 8-channel relay interface board, which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, PLC, etc.
- It is also able to control various appliances and other equipments with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Standard interface can be directly connected with microcontrollers.
- Red working status indicator lights are conducive to the safe use.
- Widely used for all MCU control, industrial sector, PLC control, smart home control.
- Input port IN1, IN2, IN3, IN4, IN5, IN6, IN7, IN8 low signal level effectively.
- VCC, GND : Input power.
- JD – VCC : Relay power input port,relay can power alone.
- Working voltage : 5V
- Module weight : about 112g
- package weight : about 150g
- module size : about 1.7cm X 5.5cm X 13.7cm(height * width * long)
- Add to cart
1-Channel Solid-State Relay is some what similar to that of a mechanical relay & the difference is that, there is no moving contact in a Solid-State Relay. Here we make use of Phototropic coupler to turn it ON and OFF.
Vivek (verified owner) –
Online best cost electronic components
Lokesh (verified owner) –
Very well worth the money.
Zohar (verified owner) –
I got my project done with these components Great Support
Viral (verified owner) –
The product is firmly packed.
Er.Prashant (verified owner) –
Good techinical knowledge
Prakash (verified owner) –
Very fast delivery.
Mayur (verified owner) –
Very well worth the money.
Er.Prashant (verified owner) –
I got my project done with these components Great Support
Viral (verified owner) –
Good support and recommended
Mayur (verified owner) –
I got my project done with these components Great Support
Prakash (verified owner) –
I got my project done with these components Great Support
Devendra (verified owner) –
Good service.