Category: Leds
Leds
Showing 1–16 of 23 results
0.22 ohm Resistor – 5 Watt
₹10.00Add to cartA resistor is a passive two-terminal electrical component that implements electrical resistance as a circuit element. In electronic circuits, resistors are used to reduce current flow, adjust signal levels, to divide voltages, bias active elements, and terminate transmission lines, among other uses.
(Note: Product Images are shown for illustrative purposes only and may differ from actual product.)
- Add to cart
One Watt LED is like choosing a resistor. The Wattage of LED will be same no matter the manufacturing industry. The difference occurs in Temperature handling and Luminous Intensity output. Â Choosing the LED with Industrial standards is always better.
2.4 V Green LED 0603 SMD
₹14.00Add to cartThe Green source color devices are made with AlGaInP on GaAs substrate Light Emitting Diode.
- Add to cart
It provides resistance of 10K ohm at 25° C.10K Ohm NTC Thermistor can measure temperatures in the range of -55°C to 125°C. It is a very economical sensor. The thermal cooling time constant for this NTC thermistor (in the air) is less than equal to 20 seconds. The thermistor is widely used in freezers, air …
3mm Green LED
₹1.00Add to cartLight Emitting Diodes (LED) are the blinky things in your circuit. Its a must for indicating power in your project or as warning indicator or a status indicator. We use LED’s for things like Power indication, relay status, to check if RF data has been received or not, warning status etc. It is a perfect low cost solution for indication and debugging purpose.
3mm Red LED
₹1.00Add to cartLight Emitting Diodes (LED) are the blinky things in your circuit. Its a must for indicating power in your project or as warning indicator or a status indicator. We use LED’s for things like Power indication, relay status, to check if RF data has been received or not, warning status etc. It is a perfect low cost solution for indication and debugging purpose.
- Add to cart
Diffused RGB Common Anode LED makes some beautiful colors with this diffused 10mm tri-color LED with separate red, green and blue LED chips inside! They make a nice indicator, and fun to color-swirl. We like diffused RGB LEDs because they color mix inside instead of appearing as 3 distinct LEDs.
5mm Green DIP LED
₹1.00Add to cartIt is a 5mm Green DIP LED. An LED is a two-lead semiconductor light source, which emits lights when activated. When an appropriate voltage is applied to the LED terminal, then the electrons are able to recombine with the electron holes within the device and release energy in the form of photons. This effect is known as electroluminescence. The color of the LED is determined by the energy bandgap of the semiconductor.
- Add to cart
5mm Round Water Clear LED Lamp For LED light, indication, illumination Viewing angle: 40 degree UV resistant epoxy With lowest power consumption, long life, and super bright
- Add to cart
IR LED is used in various daily used electronic appliances. As in the remote of the television, infrared cameras, transmission systems. We can make various projects, sensor using the IR LED like obstacle detector, visitor-counter and line-followers. An Infrared LED looks same as normal LED, but human eye is not capable of seeing the IR light as it’s beyond our visible electromagnetic spectrum. We are only able to see a light having a wavelength ranges 380 to 750nm. You can see an IR light through your phone camera, night-vision and etc.
- Add to cart
An LED is a two-lead semiconductor light source, which emits lights when activated. When an appropriate voltage is applied to the LED terminal, then the electrons are able to recombine with the electron holes within the device and release energy in the form of photons. This effect is known as electroluminescence. The color of the LED is determined by the energy band gap of the semiconductor.
5mm Yellow DIP LED
₹1.00Add to cartIt is a 5mm Blue DIP LED. An LED is a two-lead semiconductor light source, which emits lights when activated. When an appropriate voltage is applied to the LED terminal, then the electrons are able to recombine with the electron holes within the device and release energy in the form of photons. This effect is known as electroluminescence. The color of the LED is determined by the energy bandgap of the semiconductor.
- Add to cart
This 3 Volt 5mW 650nm Laser Diode is a fun little red laser that emits a laser beam similar to a laser pointer when given 3 Volts of power just like you’d get from two standard AAA or AA batteries.
Green 10mm LED
₹3.30Add to cartThis is 10mm Green LED. The size refers to the outside diameter of the LED, with 5mm being the most common LED model. 3mm LEDs are the smallest and used in tight-fitting applications. 8mm and 10mm models are used to output as much light as possible.
- Add to cart
Specification
Zero Power Resistance at 25°C 100k ohm Product Range DO-35 Standard Series Thermistor Mounting Through Hole Beta Value (K) 3892K Thermistor Case Style DO-35 Thermistor Terminals Axial Leaded Operating Temperature Min -55°C Operating Temperature Max 300°C Automotive Qualification Standard – RoHS Phthalates Compliant To Be Advised
