LM35 Temperature Sensor
Specification
- Calibrated directly in Celsius (Centigrade)
- Linear + 10.0 mV/C scale factor
- 0.5C accuracyguarantee(at +25C)
- Rated for full 55 to +150C range
- Suitable for remote applications
- Low cost due to wafer-level trimming
- Operates from 4 to 30 volts
- Less than 60 A current drain
- Low self-heating, 0.08C in still air
- Nonlinearity only14C typical
- Low impedance output, 0.1for 1 mA load
10 rpm – 12V Centre Shaft DC Geared Motor for robotics
39pf 50v Ceramic Disc Capacitor
A ceramic capacitor is a fixed-value capacitor where the ceramic material acts as the dielectric. It is constructed of two or more alternating layers of ceramic and a metal layer acting as the electrodes. The composition of the ceramic material defines the electrical behavior and therefore applications Perfect for use in various electronics projects in India, 0.000039uf/0.039nf/39pf 50v Ceramic Disc Capacitor ensures reliability and performance. Ideal for various electronics projects, 0.000039uf/0.039nf/39pf 50v Ceramic Disc Capacitor offers quality and performance.
HT-12E Encoder Decoder IC
HT12E is an encoder integrated circuit of 212 series of encoders. They are paired with 212 series of decoders for use in remote control system applications. It is mainly used in interfacing RF and infrared circuits. The chosen pair of encoder/decoder should have same number of addresses and data format.
2mm Heat Shrink Sleeve Black -10 meter
C2570A Silicon NPN Transistor – Low Noise Amplifier for VHF & UHF Stages
MQ3 Alcohol Gas Sensor Module
Specification of MQ3 GAS Sensor Module
- Power Supply : 5 Volts
- Interface Type : Analog & Digital
- High Sensitivity to Alcohol & small sensitivity to Benzine.
- Low Cost.
- Stable & Long Life.
- On board Power indication.
4.7k Resistor – 2 Watt
A resistor is a passive two-terminal electrical component that implements electrical resistance as a circuit element. In electronic circuits, resistors are used to reduce current flow, adjust signal levels, to divide voltages, bias active elements, and terminate transmission lines, among other uses.
(Note: Product Images are shown for illustrative purposes only and may differ from actual product.) Perfect for use in various electronics projects in India, 4.7k Resistor - 2 Watt ensures reliability and performance. Ideal for various electronics projects, 4.7k Resistor - 2 Watt offers quality and performance.
18650 1 Cell Battery Holder
Application of 18650 Holder
- You can use this case with your own battery to form power system supply.
- Case for rechargeable battery.
- Simple DIY recharge power supply
3mm Banana Socket Jack for Banana Plug Terminal Connector ( Black )
Features
- Withaluminum alloy core, nickel-plated, and a solid hard plastic shell, the binding post is durable and reliable, have a stable performance.
- Suitable for 4mm banana plugs, spade terminals or a bare wire, easy to install and use.
- Color-coded black/red for maintaining proper polarity.
- Ideal for speaker enclosure applications and amplifier, perfect for connecting center speakers to AV receivers
TP4056 1A Li-Ion Battery Charging Board Micro USB with Current Protection
- ThisTP4056 1A Li-Ion Battery Charging Board Micro USB with Current Protection isa tiny module, perfect for charging single cell 3.7V 1 Ah or higher lithium ion(Li-Ion) cells such as 16550s that dont have their own protection circuit. Based on the TP4056 charger IC and DW01 battery protection IC this module will offer 1A charge current then cut off when finished.
- Furthermore when the battery voltage drops below 2.4V the protection IC will switch the load off to protect the cell from running at too low of a voltage and also protects against over-voltage and reverse polarity connection (it will usually destroy itself instead of the battery) however please check you have it connected correctly the first time.
- Manufactured under fully machinery processing. so it has high reliability for the best performance. In conclusion, it is specialdesign for a single lithium battery charging.TP4056 Other features include the current monitor, under voltage lockout, automatic recharge, andtwo status pin to indicate charge termination and the presence of an input voltage.
- Using the module:
- Connect micro USB cable for power, or 5V DC to pads marked IN+ and IN- on the left-hand side of the module
- Connect cell to charge to B+/B- pads on the right-hand side of the module.
- A load (something for the battery to power) can be connected to the OUT+/OUT- pads on the right-hand side
- Important! Disconnect load when charging
- The red LED indicates charging in progress, green LED indicates charging has finished.
- Never charge your battery at a rate greater than 1C.
MG995 (Plastic) Gear Servo Motor (180 Rotation)
Features
- The connection cable is thicker.
- Equips high-quality motor.
- High resolution
- Accurate positioning
- Fast control response
- Constant torque throughout the servo travel range
- Excellent holding power