Mini 360 Step Down Buck Converter Power Supply Module
₹38.99 + GST
Specifications:
| Regulator IC | MPS MP2307DN |
| Input Voltage Range | 4.75 23VDC |
| Selectable Output Voltage | 1.0 17VDC |
| Rated Current | 1.8A Continuous 3A Surge Current |
| Maximum conversion efficiency | 95% (5Vin, 3.3Vout ~200mA output) |
| Switching Frequency | 340kHz |
| No-load output Ripple | 30mV |
| Load Regulation | ?0.5% |
| Voltage Regulation | ?2.5% |
| Operational Temperature Range(?C) | -40 to +85 |
| Length (mm) | 17 |
| Width (mm) | 11 |
| Height (mm) | 3.8 |
| Weight (gm) | 2 |
Mini 360 Step-Down Buck Converter Power Module use integrally molded power inductor and synchronous rectifier control chip, smaller and more efficient. This Module can be use as a DIY mobile power, monitor power supply, power buggies, camera power supply, car power, communications equipment supply, various right size and weight for demanding applications (such as aviation models, etc.
Features:
- Module: Non-isolated step-down module (BUCK)
- Rectification: Synchronous rectification
- Built-in 160C thermal shutdown
- Output ripple: 30mV (no-load)
You must be logged in to post a review.
Related products
- Add to cart
Relays are output devices which are used to control or operate some external devices.? This is a 5 volt Isolated relay module which means that there is a optocoupler used in between your control circuit and the relay thus protecting your circuit in case of any short circuit issues on the relay side.
Original Flex sensor 2.2 inches for Motion and Diy
₹276.73 + GSTAdd to cartFlex sensors are usually available in two sizes. One is 2.2 inch and another is 4.5 inch. Although the sizes are different the basic function remains the same. They are also divided based on resistance. There are LOW resistance, MEDIUM resistance and HIGH resistance types. Choose the appropriate type depending on requirement. ?Here we are going to discuss 2.2inch Flex sensor that is FS-L-0055.
- Add to cart
Specification
- This relay module is 5 Volts active low.
- It is an 8-channel relay interface board, which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, PLC, etc.
- It is also able to control various appliances and other equipments with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Standard interface can be directly connected with microcontrollers.
- Red working status indicator lights are conducive to the safe use.
- Widely used for all MCU control, industrial sector, PLC control, smart home control.
- Input port IN1, IN2, IN3, IN4, IN5, IN6, IN7, IN8 low signal level effectively.
- VCC, GND : Input power.
- JD – VCC : Relay power input port,relay can power alone.
- Working voltage : 5V
- Module weight : about 112g
- package weight : about 150g
- module size : about 1.7cm X 5.5cm X 13.7cm(height * width * long)
Quartz Crystal Oscillator 16MHz HC-49S 2 Pin for TV, car Electronics, PC Card, Electronic Watch, DVD, MP3v
₹6.72 + GSTAdd to cartCrystal Oscillators are used as a quick and easy way to offer circuits a very accurate and consistent frequency output. This 16 MHz Crystal is a thru-hole type and is typically used with microcontrollers.- Add to cart
1N4007 is an axial leaded general purpose rectifier in DO-41 package. This device features epoxy flame retardant, low forward voltage drop and high current capability and high reliability.
Reviews
There are no reviews yet.