MAX660 IC – CMOS Monolithic Voltage Converter IC
Original price was: ₹432.00.₹130.00Current price is: ₹130.00. + GST
- The MAX660 monolithic, charge-pump voltage inverter converts a +1.5V to +5.5V input to a corresponding -1.5V to -5.5V output. Using only two low-cost capacitors, the charge pump’s 100mA output replaces switching regulators, eliminating inductors and their associated cost, size, and EMI. Greater than 90% efficiency over most of its load-current range combined with a typical operating current of only 120µA provides ideal performance for both battery-powered and board-level voltage conversion applications. The MAX660 can also double the output voltage of an input power supply or battery, providing +9.35V at 100mA from a +5V input.
9 in stock
Related products
-
Crystal Oscillator 8 MHZ
Original price was: ₹15.00.₹6.72Current price is: ₹6.72. + GSTAdd to cartThis is a 8MHZ Crystal. This is a low cost crystal oscillator with?oscillation frequency of 8Mhz. Crystal are normally required to provide?clock pulses to your micro controller or other IC’s which require external clock?source.
An oscillator crystal has two electrically conductive plates, with a slice or?tuning fork of quartz crystal sandwiched between them. The crystal oscillator?circuit sustains oscillation by taking a voltage signal from the quartz?resonator, amplifying it, and feeding it back to the resonator. Quartz has the?further advantage that its elastic constants and its size change in such a way?that the frequency dependence on temperature can be very low.
-
16 x 2 (JHD162A) Blue/White color DC 5V Character LCD display module FOR ALL TYPE OF DEVLOMENT BOARD
Original price was: ₹200.00.₹96.76Current price is: ₹96.76. + GSTAdd to cart- Operating Voltage is 4.7V to 5.3V
- Current consumption is 1mA without backlight
- Alphanumeric LCD display module, meaning can display alphabets and numbers
- Consists of two rows and each row can print 16 characters.
- Each character is build by a 5?8 pixel box
- Can work on both 8-bit and 4-bit mode
- It can also display any custom generated characters
- Available in Blue Backlight
-
7476 Dual Master-Slave J-K Flip-Flop
Original price was: ₹90.00.₹61.50Current price is: ₹61.50. + GSTAdd to cart- Supply Voltage : 7V
- Input Voltage : 5.5V
- Operating Free Air Temperature Range : 0C to +70C
- Storage Temperature Range : 65C to +150C
-
8 Channel 5V Relay Board Expansion Module Optocoupler compatible UNO Raspberry
Original price was: ₹312.00.₹246.16Current price is: ₹246.16. + GSTAdd to cartSpecification
- This relay module is 5 Volts active low.
- It is an 8-channel relay interface board, which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, PLC, etc.
- It is also able to control various appliances and other equipments with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Standard interface can be directly connected with microcontrollers.
- Red working status indicator lights are conducive to the safe use.
- Widely used for all MCU control, industrial sector, PLC control, smart home control.
- Input port IN1, IN2, IN3, IN4, IN5, IN6, IN7, IN8 low signal level effectively.
- VCC, GND : Input power.
- JD – VCC : Relay power input port,relay can power alone.
- Working voltage : 5V
- Module weight : about 112g
- package weight : about 150g
- module size : about 1.7cm X 5.5cm X 13.7cm(height * width * long)
-
Voltage Sensor Module 25VDC
Original price was: ₹16.00.₹15.08Current price is: ₹15.08. + GSTAdd to cartThis DC Voltage Sensor Module is essentially a 5:1 potential divider circuit built using precession resistors for high accuracy.
The Arduino analog input is limited to a 5 VDC input.? If you wish to measure higher voltages,this module allows you to measure voltages of 0-25V. Keep in mind, you are restricted to voltages that are less than 25 volts. More than that and you will exceed the voltage limit of your Arduino input.
Reviews
There are no reviews yet.