2.1.5 Multi-Rotor LCD Flight Control Board with MPU for Quadcopter
₹3,883.52 + GST
The KK2.1.5 is next big evolution of the first generation KK flight control boards. The KK2.1.5 was engineered from the ground up to bring multi-rotor flight to everyone, not just the experts. The LCD screen and built in software makes install and setup easier than ever. A host of multi-rotor craft types are pre-installed, simply select your craft type, check motor layout/propeller direction, calibrate your ESCs and radio and you?re ready to go! All of which is done with easy to follow on screen prompts!
2 in stock
- Size: 50.5mm x 50.5mm x 12mm
- MCU : Atmega644 PA
- Gyro/Acc: MPU6050
- Auto-level: Yes
- Input Voltage: 4.8-6.0V
- AVR interface: standard 6 pin.
- Signal from Receiver: 1520us (5 channels).
- Signal to ESC: 1520us.
1 review for 2.1.5 Multi-Rotor LCD Flight Control Board with MPU for Quadcopter
You must be logged in to post a review.
Related products
FS CT-6B 2.4Ghz 6 Channel Remote Control RC Transmitter Receiver Control for Quadcopter
₹2,376.36 + GSTRead moreThe Flysky CT6B Remote controller is made of good quality plastic and comes in black colour
This quadcopter remote control has 6 channels and is equipped with 2.4GHz transmitter & receiver
The size of the Flysky transmitter with receiver remote controller is: (l x w x h): 28 cm x 20 cm x 10 cm
The Flysky controller package includes: 1 fly sky remote for quad rotor set (1 fs-ct6b transmitter, 1 fs-r6b receiver, 1 programming cable, 1 bind plug and 1 cd
All the contents in the package are 100% original and are in good working condition. It comes in original packaging conditionAPM 2.8 Flight Controller
₹6,068.00 + GSTAdd to cartThe APM 2.8 Multicopter Flight Controller is a complete open source autopilot system. This is the best selling technology that won the prestigious Outback Challenge UAV competition. It allows the user to turn any fixed, rotary-wing. In addition, it turns multirotor vehicle (even cars and boats) into a fully autonomous vehicle. meanwhile, it is capable of performing programmed GPS missions with waypoints.
- Add to cart
Arduino NANO Version 3 is the open source smallest Embedded Development board launched by Arduino based on Atmega328 SMD Package Microcontroller. It is a Surface mount Breadboard Friendly board integrated with Mini USB Port. DC Power Jack is not available on this Board, so power can be given through Mini USB Cable. It automatically sense and switch to the higher potential source of power, there is no need for the power select jumper.
Hobbywing XRotor 20A ESC (no BEC)
₹851.16 + GSTAdd to cartSpecification Cont Current:?20A Burst Current:?25A BEC Mode:?No BEC Lipo Cells:?2-4 NiMH :?5-12 Weight:?13g Size:?32x24x10mm
1045(10?4.5) SF Propellers Black 1CW+1CCW Set of 2 Pairs
₹140.05 + GSTAdd to cartThis is?1045(10?4.5) SF Propellers Black. They are for lower RPM motor and slow flying drone models.They have wide and thin blades in their size category which?makes them much flexible in crash conditions where they do not break easily. 1045(10?4.5) SF Propellers Black especially draws larger currents and in results will give you a considerable amount of thrust.1045(10?4.5) SF Props have high-quality propellers specially designed for multi-copters. 1045(10?4.5) SF Props has 15? angle design in the end of the propeller to avoid whirlpool multi-copter flying.
Prakash (verified owner) –
I got my project done with these components Great Support