DC Energy Meter 4 in 1, 6.5V-100V 100A (10kW) Power Meter Digital Display with Blue Back Light Voltmeter
Original price was: ₹1,749.00.₹1,560.00Current price is: ₹1,560.00. + GST
Sold out!
- Display: -Large-screen LCD displays voltage, current, active power, and energy at the same time.
- Back-Lit: -The large screen with backlight can be used even in dark environments. A short button can turn the backlight on or off.
You must be logged in to post a review.
Related products
-
Lcd 16X2 Yellow Backlight Alphanumeric Display for 8051,Avr,Arduino,Raspberry Pi,Pic,Arm All Microcontroller (Green)
Original price was: ₹112.00.₹91.82Current price is: ₹91.82. + GSTAdd to cart- Operating Voltage is 4.7V to 5.3V
- Current consumption is 1mA without backlight
- Alphanumeric LCD display module, meaning can display alphabets and numbers
- Consists of two rows and each row can print 16 characters.
- Each character is build by a 5?8 pixel box
- Can work on both 8-bit and 4-bit mode
- It can also display any custom generated characters
- Available in Green Backlight
-
BC547 NPN General Purpose Transistor
Original price was: ₹5.00.₹1.17Current price is: ₹1.17. + GSTAdd to cartBC547 is a general purpose BJT NPN transistor mostly used in electronics hobbyists and educational electronics projects. Besides these uses it can also be used in commercial circuits. It comes in TO-92 packaging and the maximum output current this transistor can handle is 100mA. The transistor is having very good DC current gain and low noise capabilities due to which it is ideal to use in signal amplification stages. The typical saturation voltage is only 90 millivolts which is also a good sign to use it as a switch.
-
Voltage Sensor Module 25VDC
Original price was: ₹16.00.₹15.08Current price is: ₹15.08. + GSTAdd to cartThis DC Voltage Sensor Module is essentially a 5:1 potential divider circuit built using precession resistors for high accuracy.
The Arduino analog input is limited to a 5 VDC input.? If you wish to measure higher voltages,this module allows you to measure voltages of 0-25V. Keep in mind, you are restricted to voltages that are less than 25 volts. More than that and you will exceed the voltage limit of your Arduino input.
-
Optocoupler High Level Relay Module Board 5V 4-CH for PIC ARM DSP AVR | Compatible with Arduno NodeMCU Raspberry Pi | Pack of 1 | Blue (Excellent Quality)
Original price was: ₹139.00.₹136.50Current price is: ₹136.50. + GSTAdd to cartSpecification
- Size : 75mm (length) x 55mm (W) x 19.3mm (height);
- Weight : 80g;
- PCB Color : Blue;
- board four weeks with four screw holes, hole diameter 3.1mm, easy to install and fixed;
- Relay selection of quality loose music relays, SPDT. A common terminal, a normally open, one normally closed terminal;
- optocoupler isolation, good anti-jamming;
- Low pull, high release. Energisation status indicator light, release status LED is off;
- VCC for the system power, JD_VCC for the relay power. Default hair 12V relay, plug the jumper cap to;
- Relay Maximum output : DC 30V/10A, AC 250V/10A
- Wiring : VCC : positive power supply system GND : System power supply negative IN1 ? IN4 : relay control ports
-
BC327 PNP General Purpose Amplifier Transistor
Original price was: ₹5.00.₹1.95Current price is: ₹1.95. + GSTAdd to cartBC327 is a general purpose PNP BJP transistor that can be used for switching and amplification purposes in electronic circuits. The transistor features 800mA collector current hence it can be used to drive variety of loads in an electronic application. The max collector-emitter voltage is -45V therefore it can easily handle load voltage under 45V. Apart from that transistor also features 625mW collector dissipation and DC current gain of maximum 630 therefore it can also be used as an audio amplifier or for any type of signal amplification.
Reviews
There are no reviews yet.