CS DC Geared Motor 6 RPM
Original price was: ₹170.00.₹162.00Current price is: ₹162.00. + GST
Features
- RPM: 6
- Operating Voltage: 12V DC
- Gearbox: Attached Plastic (spur)Gearbox
- Shaft diameter: 6mm with internal hole
- Torque: 1.2 kg-cm
- No-load current: 60 mA(Max)
- Load current: 300 mA(Max).
- gearbox covered and lubricated with lithium grease
- Requires no maintenance.
10 in stock
10 in stock
23 in stock
16 in stock
37 in stock
- A gear motor designed as an all-in-one combination of a motor and gearbox. This gearbox addition at the head to a motor comparatively reduces the speed while increasing the torque output. These Geared Motors are simply DC Motors featuring gears for the shaft for obtaining the optimal performance characteristics. Also known as the Center Shaft DC Geared Motors as their shaft extends through the center of their gearbox assembly.
- This DC Motor 6 RPM 12Volts geared designed as a simple DC motor with a metal gearbox attached to it. The metal gearbox offers better wear and tear properties. Thus it is long-lasting. This motor is widely used in all-terrain robots and a variety of robotic applications. It comes with a 3 mm threaded drill hole attached to the middle of the shaft. Thus making it quite simple to connect to the wheels or any other mechanical assembly.
Related products
-
100 MM x 2.5 MM, Nylon Zip Wire Organizer/Self Locking
Original price was: ₹10.00.₹1.64Current price is: ₹1.64. + GSTAdd to cartThis is a?100 x 2.5 mm Nylon cable tie?also known as hose tie or Zip tie. The?cable tie?is perfect for holding items together specially electric cables or wires.? The flexible design of the?cable tie?makes it easier to slip the ties under and around wire harness. Thanks to the teeth on one of the side of the belt makes it easier for self locking and securing the wires.
-
1N4148 -100V ,450mA | Diode Small Signal
Original price was: ₹1.18.₹0.90Current price is: ₹0.90. + GSTAdd to cartIt is one of the most popular and long lived switching diodes because of its dependable specifications and low cost. The 1N4148 is useful in switching applications up to about 100 MHz. The 1N4148 comes in a DO-35 glass package for thru-hole mounting.
-
8 Channel 5V Relay Board Expansion Module Optocoupler compatible UNO Raspberry
Original price was: ₹312.00.₹246.16Current price is: ₹246.16. + GSTAdd to cartSpecification
- This relay module is 5 Volts active low.
- It is an 8-channel relay interface board, which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, PLC, etc.
- It is also able to control various appliances and other equipments with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Standard interface can be directly connected with microcontrollers.
- Red working status indicator lights are conducive to the safe use.
- Widely used for all MCU control, industrial sector, PLC control, smart home control.
- Input port IN1, IN2, IN3, IN4, IN5, IN6, IN7, IN8 low signal level effectively.
- VCC, GND : Input power.
- JD – VCC : Relay power input port,relay can power alone.
- Working voltage : 5V
- Module weight : about 112g
- package weight : about 150g
- module size : about 1.7cm X 5.5cm X 13.7cm(height * width * long)
-
5V Low Level Solid State Relay Module with Fuse SSR 250V 2A Fuse
Original price was: ₹150.00.₹110.00Current price is: ₹110.00. + GSTAdd to cart1-Channel?Solid-State Relay is some what similar to that of a mechanical relay & the difference is that, there is no moving contact in a Solid-State Relay. Here we make use of Phototropic coupler to turn it ON and OFF.
-
Voltage Sensor Module 25VDC
Original price was: ₹16.00.₹15.08Current price is: ₹15.08. + GSTAdd to cartThis DC Voltage Sensor Module is essentially a 5:1 potential divider circuit built using precession resistors for high accuracy.
The Arduino analog input is limited to a 5 VDC input.? If you wish to measure higher voltages,this module allows you to measure voltages of 0-25V. Keep in mind, you are restricted to voltages that are less than 25 volts. More than that and you will exceed the voltage limit of your Arduino input.
