C7419
Original price was: ₹45.00.₹39.00Current price is: ₹39.00. + GST
5 in stock
5 in stock
12 in stock
The SF20A400HPR is an ultrafast rectifier. It has a low forward voltage drop and reverse recovery time (trr<30ns). The device is intended for use as a free wheeling, clamping rectifier in a variety of switching power supplies and other power switching applications.
Related products
-
1N4007 -1000V ,1A |DIP Rectifier Diode Rohs Lead-free Compliant
Original price was: ₹1.15.₹0.82Current price is: ₹0.82.Add to cart1N4007 is an axial leaded general purpose rectifier in DO-41 package. This device features epoxy flame retardant, low forward voltage drop and high current capability and high reliability.
-
BC327 PNP General Purpose Amplifier Transistor
Original price was: ₹5.00.₹1.95Current price is: ₹1.95. + GSTAdd to cartBC327 is a general purpose PNP BJP transistor that can be used for switching and amplification purposes in electronic circuits. The transistor features 800mA collector current hence it can be used to drive variety of loads in an electronic application. The max collector-emitter voltage is -45V therefore it can easily handle load voltage under 45V. Apart from that transistor also features 625mW collector dissipation and DC current gain of maximum 630 therefore it can also be used as an audio amplifier or for any type of signal amplification.
-
Voltage Sensor Module 25VDC
Original price was: ₹16.00.₹15.08Current price is: ₹15.08. + GSTAdd to cartThis DC Voltage Sensor Module is essentially a 5:1 potential divider circuit built using precession resistors for high accuracy.
The Arduino analog input is limited to a 5 VDC input.? If you wish to measure higher voltages,this module allows you to measure voltages of 0-25V. Keep in mind, you are restricted to voltages that are less than 25 volts. More than that and you will exceed the voltage limit of your Arduino input.
-
8 Channel 5V Relay Board Expansion Module Optocoupler compatible UNO Raspberry
Original price was: ₹312.00.₹246.16Current price is: ₹246.16. + GSTAdd to cartSpecification
- This relay module is 5 Volts active low.
- It is an 8-channel relay interface board, which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, PLC, etc.
- It is also able to control various appliances and other equipments with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Standard interface can be directly connected with microcontrollers.
- Red working status indicator lights are conducive to the safe use.
- Widely used for all MCU control, industrial sector, PLC control, smart home control.
- Input port IN1, IN2, IN3, IN4, IN5, IN6, IN7, IN8 low signal level effectively.
- VCC, GND : Input power.
- JD – VCC : Relay power input port,relay can power alone.
- Working voltage : 5V
- Module weight : about 112g
- package weight : about 150g
- module size : about 1.7cm X 5.5cm X 13.7cm(height * width * long)
-
DHT11 Module Temperature and Humidity sensor Module for boards compatible with Arduino, ARM and other MCU
Original price was: ₹120.00.₹65.00Current price is: ₹65.00. + GSTAdd to cartThe DHT11 is a commonly used Temperature and humidity sensor. The sensor comes with a dedicated NTC to measure temperature and an 8-bit microcontroller to output the values of temperature and humidity as serial data. The sensor is also factory calibrated and hence easy to interface with other microcontrollers.
