5 mm RGB LED 4 Pin Common Cathode
Original price was: ₹10.00.₹7.38Current price is: ₹7.38. + GST
Diffused RGB Common Anode LED makes some beautiful colors with this diffused 10mm tri-color LED with separate red, green and blue LED chips inside! They make a nice indicator, and fun to color-swirl. We like diffused RGB LEDs because they color mix inside instead of appearing as 3 distinct LEDs.
60 in stock
- 5 mm diameter
- Red: 623 nm wavelength, Green: 523 nm, Blue: 467 nm
- Forward Voltage, at 20mA current: Red: 1.8-2.2V, Green: 3.0-3.4V, Blue: 3.0-3.4V
- 50-degree viewing angle
1 review for 5 mm RGB LED 4 Pin Common Cathode
You must be logged in to post a review.
Related products
-
DHT11 Module Temperature and Humidity sensor Module for boards compatible with Arduino, ARM and other MCU
Original price was: ₹120.00.₹65.00Current price is: ₹65.00. + GSTAdd to cartThe DHT11 is a commonly used Temperature and humidity sensor. The sensor comes with a dedicated NTC to measure temperature and an 8-bit microcontroller to output the values of temperature and humidity as serial data. The sensor is also factory calibrated and hence easy to interface with other microcontrollers.
-
BC557 PNP General Purpose Transistor 45V 100mA TO-92 Package
Original price was: ₹5.00.₹1.17Current price is: ₹1.17. + GSTAdd to cartBC557 is a widely used PNP bipolar junction transistor manufactured in small TO-92 package. It is a general purpose PNP transistor that can be used as a switch or amplifier in electronic circuits. Its HFE ratings are 125 to 800 which makes it an ideal transistor to use as a small signal amplifier in electronic circuits for example for audio signal amplification or other, the HFE ratings of BC557 can be determined by the last letter after its number for example BC557A HFE ratings are 110-220, BC557B HFE ratings are 200-450 and BC557C HFE ratings are 420-800. The max collector dissipation is 500 milliwatt which is also an another good point to use it in amplification stages. Moreover it will also perform well when used it as a switch for load under 100mA. The transistor has also good collector to emitter (VCE) value that is -45V, therefore you can easily use it in circuits using 40 to 45 volts DC.
-
8 Channel 5V Relay Board Expansion Module Optocoupler compatible UNO Raspberry
Original price was: ₹312.00.₹246.16Current price is: ₹246.16. + GSTAdd to cartSpecification
- This relay module is 5 Volts active low.
- It is an 8-channel relay interface board, which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, PLC, etc.
- It is also able to control various appliances and other equipments with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Standard interface can be directly connected with microcontrollers.
- Red working status indicator lights are conducive to the safe use.
- Widely used for all MCU control, industrial sector, PLC control, smart home control.
- Input port IN1, IN2, IN3, IN4, IN5, IN6, IN7, IN8 low signal level effectively.
- VCC, GND : Input power.
- JD – VCC : Relay power input port,relay can power alone.
- Working voltage : 5V
- Module weight : about 112g
- package weight : about 150g
- module size : about 1.7cm X 5.5cm X 13.7cm(height * width * long)
-
Lcd 16X2 Yellow Backlight Alphanumeric Display for 8051,Avr,Arduino,Raspberry Pi,Pic,Arm All Microcontroller (Green)
Original price was: ₹112.00.₹91.82Current price is: ₹91.82. + GSTAdd to cart- Operating Voltage is 4.7V to 5.3V
- Current consumption is 1mA without backlight
- Alphanumeric LCD display module, meaning can display alphabets and numbers
- Consists of two rows and each row can print 16 characters.
- Each character is build by a 5?8 pixel box
- Can work on both 8-bit and 4-bit mode
- It can also display any custom generated characters
- Available in Green Backlight
-
5V Low Level Solid State Relay Module with Fuse SSR 250V 2A Fuse
Original price was: ₹150.00.₹110.00Current price is: ₹110.00. + GSTAdd to cart1-Channel?Solid-State Relay is some what similar to that of a mechanical relay & the difference is that, there is no moving contact in a Solid-State Relay. Here we make use of Phototropic coupler to turn it ON and OFF.
Rahul (verified owner) –
Very well worth the money.