PH Sensor Module and PH Electrode Probe Kit – High Quality
₹2,454.40
Specifications:-
| Input Supply voltage (VDC) | Â 5 |
| Module Size (mm) | 50 x 47 x 16 |
| Measuring Range | 0 14 PH |
| Measuring Temperature | 0 50 |
| Accuracy | 0.01 pH |
| Response Time | 1min |
| Cable Length (cm) | 75 |
| pH sensor size (mm) | 150, 12 |
2 in stock
- The Analog pH Sensor Kit is specially designed for Arduino controllers and has a built-in simple, convenient, and practical connection and features. It has an LED that works as the Power Indicator, a BNC connector, and a PH2.0 sensor interface. To use it, just connect the pH sensor with the BND connector, and plug the PH2.0 interface into the analog input port of any Arduino controller. If pre-programmed, you will get the pH value easily. Comes in a compact plastic box with foams for better mobile storage
- Applications
- Water quality testing
- Aquaculture
Related products
Add to cartThe DHT11 is a commonly used Temperature and humidity sensor. The sensor comes with a dedicated NTC to measure temperature and an 8-bit microcontroller to output the values of temperature and humidity as serial data. The sensor is also factory calibrated and hence easy to interface with other microcontrollers.
- Add to cart
Specification
- This relay module is 5 Volts active low.
- It is an 8-channel relay interface board, which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, PLC, etc.
- It is also able to control various appliances and other equipments with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Standard interface can be directly connected with microcontrollers.
- Red working status indicator lights are conducive to the safe use.
- Widely used for all MCU control, industrial sector, PLC control, smart home control.
- Input port IN1, IN2, IN3, IN4, IN5, IN6, IN7, IN8 low signal level effectively.
- VCC, GND : Input power.
- JD – VCC : Relay power input port,relay can power alone.
- Working voltage : 5V
- Module weight : about 112g
- package weight : about 150g
- module size : about 1.7cm X 5.5cm X 13.7cm(height * width * long)
Add to cart1-Channel Solid-State Relay is some what similar to that of a mechanical relay & the difference is that, there is no moving contact in a Solid-State Relay. Here we make use of Phototropic coupler to turn it ON and OFF.
Add to cartSpecification
- Size : 75mm (length) x 55mm (W) x 19.3mm (height);
- Weight : 80g;
- PCB Color : Blue;
- board four weeks with four screw holes, hole diameter 3.1mm, easy to install and fixed;
- Relay selection of quality loose music relays, SPDT. A common terminal, a normally open, one normally closed terminal;
- optocoupler isolation, good anti-jamming;
- Low pull, high release. Energisation status indicator light, release status LED is off;
- VCC for the system power, JD_VCC for the relay power. Default hair 12V relay, plug the jumper cap to;
- Relay Maximum output : DC 30V/10A, AC 250V/10A
- Wiring : VCC : positive power supply system GND : System power supply negative IN1 – IN4 : relay control ports
Crystal Oscillator 8 MHZ
₹8.20Add to cartThis is a 8MHZ Crystal. This is a low cost crystal oscillator with oscillation frequency of 8Mhz. Crystal are normally required to provide clock pulses to your micro controller or other IC’s which require external clock source.
An oscillator crystal has two electrically conductive plates, with a slice or tuning fork of quartz crystal sandwiched between them. The crystal oscillator circuit sustains oscillation by taking a voltage signal from the quartz resonator, amplifying it, and feeding it back to the resonator. Quartz has the further advantage that its elastic constants and its size change in such a way that the frequency dependence on temperature can be very low.
Reviews
There are no reviews yet.