Search Results for: analog inputs
Showing all 4 results
-
ATTINY85V2 Digispark ATTiny85 USB Development Board Digistump Mini
Original price was: ₹400.00.₹210.00Current price is: ₹210.00. + GSTAdd to cartSpecification
-
- Support for the IDE 1.0+ (OSX / Win / Linux)
- Power via USB or External Source – 5V or 7 -35V (automatic selection)
-
- On-board 500ma 5V Regulator
-
- Built-in USB(and serial debugging)
-
- 6 I/O Pins (2 are used for USB only if your program actively communicates over USB otherwise you can use all 6 even if you are programming via USB)
-
- 8k Flash Memory (about 6K after bootloader)
-
- I2C and SPI(vis USI)
-
- PWM on 3 pins (more possible with Software PWM)
-
- ADC on 4 pins
-
- Power LED and Test/ Status LED (on Pin0)
-
- Weight : 4g
-
-
ADS1115 16-Bit I2C ADC 4-Channel Programmable Gain Amplifier Module
Original price was: ₹185.00.₹156.00Current price is: ₹156.00. + GSTAdd to cartFeatures
- WIDE SUPPLY RANGE: 2.0V to 5.5V
- PROGRAMMABLE DATA RATE: 8SPS to 860SPS
- It has an Internal low-drift voltage reference
- Internal Oscillator.
- Internal PGA.
- I2C INTERFACE : Pin-Selectable Addresses.
- Four single ends Or Two differential inputs.
-
LM3915 LED Dot/Bar Display Driver IC DIP-18 Package
Original price was: ₹40.00.₹28.93Current price is: ₹28.93. + GSTAdd to cartSpecification:-
Parameter Value Power Dissipation (3) PDIP (NFK) 1365 mW 1365 mW Supply Voltage 25V Voltage on Output Drivers 25V Input Signal Overvoltage +-35V Divider Voltage -100mV to V+ Reference Load Current 10 mA Storage Temperature Range -55?C to 150?C Lead Temperature (Soldering, 10 sec.) 260?C ?
-
LM3914 Dot/Bar Display Driver IC DIP-18 Package
Original price was: ₹78.00.₹22.10Current price is: ₹22.10. + GSTRead moreThe LM3914 is a monolithic integrated circuit that senses analog voltage levels and drives 10 LEDs, providing a linear analog display. A single pin changes the display from a moving dot to a bar graph. Current drive to the LEDs is regulated and programmable, eliminating the need for resistors. This feature is one that allows operation of the whole system from less than 3V.
The circuit contains its own adjustable reference and accurate 10-step voltage divider. The low-bias-current input buffer accepts signals down to ground, or V?, yet needs no protection against inputs of 35V above or below ground. The buffer drives 10 individual comparators referenced to the precision divider. Indication non-linearity can thus be held typically to ?%, even over a wide temperature range.
Versatility was designed into the LM3914 so that controller, visual alarm, and expanded scale functions are easily added on to the display system. The circuit can drive LEDs of many colors, or low-current incandescent lamps. Many LM3914s can be ?chained? to form displays of 20 to over 100 segments. Both ends of the voltage divider are externally available so that 2 drivers can be made into a zero-center meter.
The LM3914 is very easy to apply as an analog meter circuit. A 1.2V full-scale meter requires only 1 resistor and a single 3V to 15V supply in addition to the 10 display LEDs. If the 1 resistor is a pot, it becomes the LED brightness control. The simplified block diagram illustrates this extremely simple external circuitry.
When in the dot mode, there is a small amount of overlap or ?fade? (about 1 mV) between segments. This assures that at no time will all LEDs be ?OFF?, and thus any ambiguous display is avoided. Various novel displays are possible.
Much of the display flexibility derives from the fact that all outputs are individual, DC regulated currents. Various effects can be achieved by modulating these currents. The individual outputs can drive a transistor as well as a LED at the same time, so controller functions including ?staging? control can be performed. The LM3914 can also act as a programmer, or sequencer.
The LM3914 is rated for operation from 0?C to +70?C. The LM3914N-1 is available in an 18-lead PDIP (NFK) package.