XL6009 DC-DC Adjustable Step-up Boost Power Converter Board Module

Related products

• Sale!

  Rated 4.67 out of 5

  DHT11 Module Temperature and Humidity sensor Module for boards compatible with Arduino, ARM and other MCU

  ₹120.00 ₹104.00

  The DHT11 is a commonly used Temperature and humidity sensor. The sensor comes with a dedicated NTC to measure temperature and an 8-bit microcontroller to output the values of temperature and humidity as serial data. The sensor is also factory calibrated and hence easy to interface with other microcontrollers.

  Add to cart

  Quick View
• Sale!

  Rated 4.48 out of 5

  Original Flex sensor 2.2 inches for Motion and Diy

  ₹400.00 ₹350.00

  Flex sensors are usually available in two sizes. One is 2.2 inch and another is 4.5 inch. Although the sizes are different the basic function remains the same. They are also divided based on resistance. There are LOW resistance, MEDIUM resistance and HIGH resistance types. Choose the appropriate type depending on requirement.  Here we are going to discuss 2.2inch Flex sensor that is FS-L-0055.

  Add to cart

  Quick View
• Sale!

  Rated 5.00 out of 5

  BC557 PNP General Purpose Transistor 45V 100mA TO-92 Package

  ₹5.00 ₹1.03

  BC557 is a widely used PNP bipolar junction transistor manufactured in small TO-92 package. It is a general purpose PNP transistor that can be used as a switch or amplifier in electronic circuits. Its HFE ratings are 125 to 800 which makes it an ideal transistor to use as a small signal amplifier in electronic circuits for example for audio signal amplification or other, the HFE ratings of BC557 can be determined by the last letter after its number for example BC557A HFE ratings are 110-220, BC557B HFE ratings are 200-450 and BC557C HFE ratings are 420-800. The max collector dissipation is 500 milliwatt which is also an another good point to use it in amplification stages. Moreover it will also perform well when used it as a switch for load under 100mA. The transistor has also good collector to emitter (VCE) value that is -45V, therefore you can easily use it in circuits using 40 to 45 volts DC.

  Add to cart

  Quick View
• 

  Optocoupler High Level Relay Module Board 5V 4-CH for PIC ARM DSP AVR | Compatible with Arduno NodeMCU Raspberry Pi | Pack of 1 | Blue (Excellent Quality)

  ₹176.64

  Specification

  • Size : 75mm (length) x 55mm (W) x 19.3mm (height);

  • Weight : 80g;

  • PCB Color : Blue;

  • board four weeks with four screw holes, hole diameter 3.1mm, easy to install and fixed;

  • Relay selection of quality loose music relays, SPDT. A common terminal, a normally open, one normally closed terminal;

  • optocoupler isolation, good anti-jamming;

  • Low pull, high release. Energisation status indicator light, release status LED is off;

  • VCC for the system power, JD_VCC for the relay power. Default hair 12V relay, plug the jumper cap to;

  • Relay Maximum output : DC 30V/10A, AC 250V/10A

  • Wiring : VCC : positive power supply system GND : System power supply negative IN1 – IN4 : relay control ports

  Add to cart

  Quick View
• Sale!

  Rated 4.00 out of 5

  Crystal Oscillator 8 MHZ

  ₹15.00 ₹8.20

  This is a 8MHZ Crystal. This is a low cost crystal oscillator with oscillation frequency of 8Mhz. Crystal are normally required to provide clock pulses to your micro controller or other IC’s which require external clock source.

  An oscillator crystal has two electrically conductive plates, with a slice or tuning fork of quartz crystal sandwiched between them. The crystal oscillator circuit sustains oscillation by taking a voltage signal from the quartz resonator, amplifying it, and feeding it back to the resonator. Quartz has the further advantage that its elastic constants and its size change in such a way that the frequency dependence on temperature can be very low.

  Add to cart

  Quick View