Turbidity Detection Sensor Kit | Liquid Water Particles Value Detection Sensor Module compatible with Arduino
₹817.62 + GST
Specifications :-
| Working voltage | DC 5V |
| Working current | 30mA [MAX] |
| Response time | <500 msec |
| Insulation Resistance | 100M [Min] |
| Operating Temperature (C) | -30 ~ +80 |
| Length (mm) | 33 |
| Width (mm) | 20 |
| Height (mm) | 12 |
| Weight (gm) | 55 |
3 in stock
- This is a Turbidity Sensor with Module, an electronic monitoring module specially developed to work with microcontroller platforms Arduino, Raspberry Pi, PIC, ARM, AVR, among others.
- It is very efficient, the Arduino Turbidity Sensor is able to detect and verify the quality of the water, making the turbidity measurement, where it is possible to verify the results by means of digital or analog signal next to the corresponding pins in the accompanying electronic module.
- The Turbidity Sensor emits at its end an infrared light, imperceptible to human vision, capable of detecting particles that are suspended in water, measuring the light transmittance and the dispersion rate, which changes according to the Amount of TSS (Total Suspended Solids), increasing the turbidity of the liquid whenever levels increase.
- In general, the Arduino Turbidity Sensor is applied in projects involving the monitoring of water turbidity in rivers, streams, lakes, water bodies, catchment and research sites, laboratories, tanks with liquids and so on. This Turbidity Sensor has an end specially prepared for direct contact, having an electronic module to amplify and send the received data to the microcontroller of the project
Theory of Operation
The sensor operates on the principle that when the light is passed through a sample of water, the amount of light transmitted through the sample is dependent on the amount of soil in the water. As the soil level increases, the amount of transmitted light decreases. The turbidity sensor measures the amount of transmitted light to determine the turbidity of the wash water. These turbidity measurements are sent to the dishwasher controller, which makes decisions on how long to wash in all the cycles.
These decisions are made on the basis of a comparison between clean water measurements (taken at the beginning of the wash cycle) and the wash water turbidity measurement taken at the end of each wash cycle. By measuring the turbidity of the wash water, the dishwasher can conserve energy on lightly soiled loads by only washing as long as necessary. This will result in energy savings for the consumer.
1 review for Turbidity Detection Sensor Kit | Liquid Water Particles Value Detection Sensor Module compatible with Arduino
You must be logged in to post a review.
Related products
Original Flex sensor 2.2 inches for Motion and Diy
₹276.73 + GSTAdd to cartBuy nowFlex sensors are usually available in two sizes. One is 2.2 inch and another is 4.5 inch. Although the sizes are different the basic function remains the same. They are also divided based on resistance. There are LOW resistance, MEDIUM resistance and HIGH resistance types. Choose the appropriate type depending on requirement. ?Here we are going to discuss 2.2inch Flex sensor that is FS-L-0055.
1N4148 -100V ,450mA | Diode Small Signal
₹0.90 + GSTAdd to cartBuy nowIt is one of the most popular and long lived switching diodes because of its dependable specifications and low cost. The 1N4148 is useful in switching applications up to about 100 MHz. The 1N4148 comes in a DO-35 glass package for thru-hole mounting.
- Add to cartBuy now
Relays are output devices which are used to control or operate some external devices.? This is a 5 volt Isolated relay module which means that there is a optocoupler used in between your control circuit and the relay thus protecting your circuit in case of any short circuit issues on the relay side.
- Add to cartBuy now
- Decade counter/decimal decode display (CD4017B)
- Binary counter/decoder
- Frequency division
- Counter control/timers
- Divde-by-N counting
- For further application information, see ICAN-6166 “COS/MOS MSI Counter and Register Design and Applications”
- Add to cartBuy now
Specification
- Size : 75mm (length) x 55mm (W) x 19.3mm (height);
- Weight : 80g;
- PCB Color : Blue;
- board four weeks with four screw holes, hole diameter 3.1mm, easy to install and fixed;
- Relay selection of quality loose music relays, SPDT. A common terminal, a normally open, one normally closed terminal;
- optocoupler isolation, good anti-jamming;
- Low pull, high release. Energisation status indicator light, release status LED is off;
- VCC for the system power, JD_VCC for the relay power. Default hair 12V relay, plug the jumper cap to;
- Relay Maximum output : DC 30V/10A, AC 250V/10A
- Wiring : VCC : positive power supply system GND : System power supply negative IN1 ? IN4 : relay control ports
Lokesh (verified owner) –
Good techinical knowledge