TDA2003 10W Audio Amplifier
₹23.01
25 in stock
Features-
- Vs Peak supply voltage (50 ms): 40 V
- Vs DC supply voltage: 28 V
- Vs Operating supply voltage: 18 V
- Io Output peak current (non-repetitive): 4.5 A
- Io Output peak current (repetitive): 3.5 A
- Ptot Power dissipation at T case = 90 °C: 20 W
- Tstg, Tj Storage and junction temperature: -40 to 150 °C
- High output current (up to 3.5 A)
- very low harmonic and crossover distortion
- DC and AC short-circuit protection between all pins and ground
- thermal limiting circuit
- load dump voltage surge protection up to 40 V
- protection diodes in case of accidental open ground
Related products
Crystal Oscillator 8 MHZ
₹8.20Add to cartThis is a 8MHZ Crystal. This is a low cost crystal oscillator with oscillation frequency of 8Mhz. Crystal are normally required to provide clock pulses to your micro controller or other IC’s which require external clock source.
An oscillator crystal has two electrically conductive plates, with a slice or tuning fork of quartz crystal sandwiched between them. The crystal oscillator circuit sustains oscillation by taking a voltage signal from the quartz resonator, amplifying it, and feeding it back to the resonator. Quartz has the further advantage that its elastic constants and its size change in such a way that the frequency dependence on temperature can be very low.
- Add to cart
BC557 is a widely used PNP bipolar junction transistor manufactured in small TO-92 package. It is a general purpose PNP transistor that can be used as a switch or amplifier in electronic circuits. Its HFE ratings are 125 to 800 which makes it an ideal transistor to use as a small signal amplifier in electronic circuits for example for audio signal amplification or other, the HFE ratings of BC557 can be determined by the last letter after its number for example BC557A HFE ratings are 110-220, BC557B HFE ratings are 200-450 and BC557C HFE ratings are 420-800. The max collector dissipation is 500 milliwatt which is also an another good point to use it in amplification stages. Moreover it will also perform well when used it as a switch for load under 100mA. The transistor has also good collector to emitter (VCE) value that is -45V, therefore you can easily use it in circuits using 40 to 45 volts DC.
- Add to cart
Specification
- This relay module is 5 Volts active low.
- It is an 8-channel relay interface board, which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, PLC, etc.
- It is also able to control various appliances and other equipments with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Standard interface can be directly connected with microcontrollers.
- Red working status indicator lights are conducive to the safe use.
- Widely used for all MCU control, industrial sector, PLC control, smart home control.
- Input port IN1, IN2, IN3, IN4, IN5, IN6, IN7, IN8 low signal level effectively.
- VCC, GND : Input power.
- JD – VCC : Relay power input port,relay can power alone.
- Working voltage : 5V
- Module weight : about 112g
- package weight : about 150g
- module size : about 1.7cm X 5.5cm X 13.7cm(height * width * long)
- Read more
Flex sensors are usually available in two sizes. One is 2.2 inch and another is 4.5 inch. Although the sizes are different the basic function remains the same. They are also divided based on resistance. There are LOW resistance, MEDIUM resistance and HIGH resistance types. Choose the appropriate type depending on requirement. Â Here we are going to discuss 2.2inch Flex sensor that is FS-L-0055.
- Read more
Relays are output devices which are used to control or operate some external devices. This is a 5 volt Isolated relay module which means that there is a optocoupler used in between your control circuit and the relay thus protecting your circuit in case of any short circuit issues on the relay side.
Reviews
There are no reviews yet.