D718 Datasheet ? 120V, 8A, NPN Transistor
₹60.00 ₹42.90 + GST
Specification
- Maximum Ratings ( Ta=25?C )
- 1. Collector-Base Voltage : Vcbo = 120V
- 2. Collector-Emitter Voltage : Vceo = 120V
- 3. Emitter-Base Voltage : Vebo = 5V
- 4. Collector Current : Ic = 8A
- 5. Base Current : Ib = 0.8A
- 6. Collector Power Dissipation : Pc = 80W
19 in stock
Purchase & earn 43 SmartX Rewards Coin!- This transistor designed for use in general-purpose amplifier and switching application.
1 review for D718 Datasheet ? 120V, 8A, NPN Transistor
You must be logged in to post a review.
Related products
- Purchase & earn 15 SmartX Rewards Coin!Add to cartBuy now
This DC Voltage Sensor Module is essentially a 5:1 potential divider circuit built using precession resistors for high accuracy.
The Arduino analog input is limited to a 5 VDC input.? If you wish to measure higher voltages,this module allows you to measure voltages of 0-25V. Keep in mind, you are restricted to voltages that are less than 25 volts. More than that and you will exceed the voltage limit of your Arduino input.
- Rated 5.00 out of 5
8 Channel 5V Relay Board Expansion Module Optocoupler compatible UNO Raspberry
₹312.00₹246.16 + GSTPurchase & earn 246 SmartX Rewards Coin!Add to cartBuy nowSpecification
- This relay module is 5 Volts active low.
- It is an 8-channel relay interface board, which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, PLC, etc.
- It is also able to control various appliances and other equipments with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Standard interface can be directly connected with microcontrollers.
- Red working status indicator lights are conducive to the safe use.
- Widely used for all MCU control, industrial sector, PLC control, smart home control.
- Input port IN1, IN2, IN3, IN4, IN5, IN6, IN7, IN8 low signal level effectively.
- VCC, GND : Input power.
- JD – VCC : Relay power input port,relay can power alone.
- Working voltage : 5V
- Module weight : about 112g
- package weight : about 150g
- module size : about 1.7cm X 5.5cm X 13.7cm(height * width * long)
- Purchase & earn 1 SmartX Rewards Coins!Add to cartBuy now
BC547 is a general purpose BJT NPN transistor mostly used in electronics hobbyists and educational electronics projects. Besides these uses it can also be used in commercial circuits. It comes in TO-92 packaging and the maximum output current this transistor can handle is 100mA. The transistor is having very good DC current gain and low noise capabilities due to which it is ideal to use in signal amplification stages. The typical saturation voltage is only 90 millivolts which is also a good sign to use it as a switch.
- Rated 5.00 out of 5
5V Low Level Solid State Relay Module with Fuse SSR 250V 2A Fuse
₹150.00₹110.00 + GSTPurchase & earn 110 SmartX Rewards Coin!Add to cartBuy now1-Channel?Solid-State Relay is some what similar to that of a mechanical relay & the difference is that, there is no moving contact in a Solid-State Relay. Here we make use of Phototropic coupler to turn it ON and OFF.
- Purchase & earn 1 SmartX Rewards Coins!Add to cartBuy now
It is one of the most popular and long lived switching diodes because of its dependable specifications and low cost. The 1N4148 is useful in switching applications up to about 100 MHz. The 1N4148 comes in a DO-35 glass package for thru-hole mounting.
Jayen (verified owner) –
Good service.