Nema 17 3D Printer 2-phase 4-wire Stepper Motor for 1.8Deg 17HD34008-22B
₹521.00
Specification
- Step Angle : 1.8°
- Current/Phase : 1.7 Amp
- Resistance/Phase : 1.65 Ohm
- Inductance/Phase : 3.2 mH
- Holding Torque : 4.0 kg.cm
- No. of Leads : 4
- Detent Torque : 150 g.cm
- Rotor Inertia : 54 g.cm
- Mass : 0.28 Kg
- Temperature Rise : 80°Cmax
- Ambient Temperature : -20°C~+50°C
- Insulation Resistance : 100 MO Min.,500VDC
- Dielectric Strength : 500VAC for 1minute
- Shaft Radial Play : 0.02Max. (450g-load)
- Shaft Axial Play : 0.08Max. (450g-load)
- Max. radial force : 28N (20mm from the flange)
- Max. axial force : 10N
- Motor Length : 40(mm)
5 in stock
5 in stock
10 in stock
- 1m wire, one connect electrical machine, on the other end has variety optional ports; heat shrink tubing effect to prevent the wire tangled up
- Suitable for 17HD3400822B mixing type stepping motor
- Outside view: Show as the picture
- Drive mode: Chopping wave constant current Drive
- Exciting mode: Twophase 4wire, it is available for rotation of forward and reverse
- Turn to: the order of power is ABBCCDDA, from shaft end see C.W
- Rated current (onephase): 1.5A DC
- Rated voltage: 3.45V
- Stepping angle: 1.8°
- Specifics:
- Operating Conditions: Environment Temperature: 20~50℃; RH: 90%MAX; Mounting Position: Axis horizontal or vertical installation
- Directcurrent winding resistance (25℃): 2.3&;±10%
- Wnding inductance: 3mH±20%
- Cogging torque: 12mN.m REF.
- Holding torque: ≥300mN.m（I=1.5A）
- Max. noload starting frequency: ≥1500pps
- Max. noload running frequency: ≥8000pps
- Temperature rise: <80K
12 reviews for Nema 17 3D Printer 2-phase 4-wire Stepper Motor for 1.8Deg 17HD34008-22B
You must be logged in to post a review.
Related products
- Add to cart
A DC motor clamp or a bracket is used to mount the motor tightly on any solid surface. Thus it increases the usability of the motor & makes motor mounting very convenient. This clamp or mount bracket is designed for DC Geared Motors
Add to cartL293D PowerDIP-16 Stepper Motor Controller/ Driver is a dual H-bridge motor driver integrated circuit (IC). Motor drivers act as current amplifiers since they take a low-current control signal and provide a higher-current signal. This higher current signal is used to drive the motors.
- Add to cart
Robot Wheel 10cm Dia. x 2cm WidthWheels for your robot are easy to mount, durable and cheap. These wheels have a 6mm hole for a shaft with a screw for fitting making it very easy to mount on motors.
- Add to cart
This is Robot Wheel 2. Wheels for your robot, easy to mount, durable and cheap. These wheels have a 6mm hole for the shaft with the screw for fitting making it very easy to mount on motors.
2000 RPM-12V Geared Motors
₹159.00Add to cartDC Motor – 2000RPM – 12Volts geared motors are generally a simple DC motor with a gearbox attached to it. This can be used in all-terrain robots and variety of robotic applications. These motors have a 3 mm threaded drill hole in the middle of the shaft thus making it simple to connect it to the wheels or any other mechanical assembly.
Jayen (verified owner) –
Best cost electronic components in India
Ketan (verified owner) –
Less cost than other websites
Ketan (verified owner) –
Good support and recommended
Rohit (verified owner) –
I got my project done with these components Great Support
Mayur (verified owner) –
Good support and recommended
Priya (verified owner) –
I got my project done with these components Great Support
Vikas (verified owner) –
Online best cost electronic components
Ketan (verified owner) –
Online best cost electronic components
Prakash (verified owner) –
Very well worth the money.
Shubham (verified owner) –
Less cost than other websites
Er.Prashant (verified owner) –
Good quality.
Zohar (verified owner) –
Drone parts i ordered and found ok