Green 10mm LED
₹5.00 ₹2.71 + GST
This is?10mm Green LED. The size refers to the outside diameter of the LED, with 5mm being the most common LED model. 3mm LEDs are the smallest and used in tight-fitting applications. 8mm and 10mm models are used to output as much light as possible.
90 in stock
Purchase & earn 3 SmartX Rewards Coin!- 520-525nm Green
- 3.0-3.4VDC Forward Voltage
- 20mA Forward Current
- 40 degree viewing angle
- 150-180 MCD output
1 review for Green 10mm LED
You must be logged in to post a review.
Related products
- Rated 5.00 out of 5
8 Channel 5V Relay Board Expansion Module Optocoupler compatible UNO Raspberry
₹312.00₹246.16 + GSTPurchase & earn 246 SmartX Rewards Coin!Add to cartBuy nowSpecification
- This relay module is 5 Volts active low.
- It is an 8-channel relay interface board, which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, PLC, etc.
- It is also able to control various appliances and other equipments with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Standard interface can be directly connected with microcontrollers.
- Red working status indicator lights are conducive to the safe use.
- Widely used for all MCU control, industrial sector, PLC control, smart home control.
- Input port IN1, IN2, IN3, IN4, IN5, IN6, IN7, IN8 low signal level effectively.
- VCC, GND : Input power.
- JD – VCC : Relay power input port,relay can power alone.
- Working voltage : 5V
- Module weight : about 112g
- package weight : about 150g
- module size : about 1.7cm X 5.5cm X 13.7cm(height * width * long)
- Rated 4.55 out of 5
Quality ESP-12F ESP8266 Remote Serial Port WIFI Transceiver Wireless Module
₹130.00₹97.00 + GSTPurchase & earn 97 SmartX Rewards Coin!Add to cartBuy nowCore processor ESP8266 in smaller sizes of the module encapsulates Tensilica L106 integrates industry-leading ultra low power 32-bit MCU micro, with the 16-bit short mode, Clock speed support 80 MHz, 160 MHz, supports the RTOS, integrated Wi Fi MAC/BB/RF/PA/LNA, on-board antenna. - Purchase & earn 2 SmartX Rewards Coin!Add to cartBuy now
2N2222 is NPN BJT?normally used in low power amplifiers and also for switching application.
2n2222 is used as a?small signal transistor?and used as a general purpose transistor and is very popular. ?This is in TO-92 package form.
- Purchase & earn 15 SmartX Rewards Coin!Add to cartBuy now
This DC Voltage Sensor Module is essentially a 5:1 potential divider circuit built using precession resistors for high accuracy.
The Arduino analog input is limited to a 5 VDC input.? If you wish to measure higher voltages,this module allows you to measure voltages of 0-25V. Keep in mind, you are restricted to voltages that are less than 25 volts. More than that and you will exceed the voltage limit of your Arduino input.
- Purchase & earn 1 SmartX Rewards Coins!Add to cartBuy now
BC547 is a general purpose BJT NPN transistor mostly used in electronics hobbyists and educational electronics projects. Besides these uses it can also be used in commercial circuits. It comes in TO-92 packaging and the maximum output current this transistor can handle is 100mA. The transistor is having very good DC current gain and low noise capabilities due to which it is ideal to use in signal amplification stages. The typical saturation voltage is only 90 millivolts which is also a good sign to use it as a switch.
Prakash (verified owner) –
Good techinical knowledge