Quality ESP-12F ESP8266 Remote Serial Port WIFI Transceiver Wireless Module
₹181.00
10 in stock
- 802.11 b/g/n
- Integrated low power 32-bit MCU
- Integrated 10-bit ADC
- Integrated TCP/IP protocol stack
- Integrated TR switch, balun, LNA, power amplifier and matching network
- Integrated PLL, regulators, and power management units
- Supports antenna diversity
- Wi-Fi 2.4 GHz, support WPA/WPA2
- Support STA/AP/STA+AP operation modes
- Support Smart Link Function for both Android and iOS devices
- SDIO 2.0, (H) SPI, UART, I2C, I2S, IRDA, PWM, GPIO
- STBC, 1×1 MIMO, 2×1 MIMO
- A-MPDU & A-MSDU aggregation and 0.4s guard interval
- Deep sleep power <10uA, Power down leakage current < 5uA
- Wake up and transmit packets in < 2ms
- Standby power consumption of < 1.0mW (DTIM3)
- +20dBm output power in 802.11b mode
- Operating temperature range -40C ~ 125C
- FCC, CE, and ROSH certified
11 reviews for Quality ESP-12F ESP8266 Remote Serial Port WIFI Transceiver Wireless Module
Related products
- Add to cart
Relays are output devices which are used to control or operate some external devices. This is a 5 volt Isolated relay module which means that there is a optocoupler used in between your control circuit and the relay thus protecting your circuit in case of any short circuit issues on the relay side.
Add to cart2N2222 is NPN BJTÂ normally used in low power amplifiers and also for switching application.
2n2222 is used as a small signal transistor and used as a general purpose transistor and is very popular.  This is in TO-92 package form.
Crystal Oscillator 8 MHZ
₹8.20Add to cartThis is a 8MHZ Crystal. This is a low cost crystal oscillator with oscillation frequency of 8Mhz. Crystal are normally required to provide clock pulses to your micro controller or other IC’s which require external clock source.
An oscillator crystal has two electrically conductive plates, with a slice or tuning fork of quartz crystal sandwiched between them. The crystal oscillator circuit sustains oscillation by taking a voltage signal from the quartz resonator, amplifying it, and feeding it back to the resonator. Quartz has the further advantage that its elastic constants and its size change in such a way that the frequency dependence on temperature can be very low.
Add to cartThe DHT11 is a commonly used Temperature and humidity sensor. The sensor comes with a dedicated NTC to measure temperature and an 8-bit microcontroller to output the values of temperature and humidity as serial data. The sensor is also factory calibrated and hence easy to interface with other microcontrollers.
Add to cartBC547 is a general purpose BJT NPN transistor mostly used in electronics hobbyists and educational electronics projects. Besides these uses it can also be used in commercial circuits. It comes in TO-92 packaging and the maximum output current this transistor can handle is 100mA. The transistor is having very good DC current gain and low noise capabilities due to which it is ideal to use in signal amplification stages. The typical saturation voltage is only 90 millivolts which is also a good sign to use it as a switch.
Vikas (verified owner) –
Best cost electronic components in India
Prakash (verified owner) –
Best cost electronic components in India
Sneha (verified owner) –
I got my project done with these components Great Support
Zohar (verified owner) –
Good quality.
Roma (verified owner) –
I got my project done with these components Great Support
Roma (verified owner) –
Best cost electronic components in India
Ayush (verified owner) –
Drone parts i ordered and found ok
Vikas (verified owner) –
Drone parts i ordered and found ok
Vikas (verified owner) –
Good techinical knowledge
Devendra (verified owner) –
Good service.
Rohit (verified owner) –
The product is firmly packed.