6 Pin 2 Way Toggle Switch 3A/5A AC 250V/125V DPDT On Off, 250v for DIY
₹30.00 ₹19.75
It is a Mini MTS-203 6-Pin DPDT 6A 125VAC Toggle Switch. The switch is Double Pole Double Throw with 6 pins.
31 in stock
Purchase & earn 20 SmartX Rewards Coin!- Double Pole Double Throw.
- Main Body: 12 x 12 x 10mm.
- Lever Length: 11mm.
1 review for 6 Pin 2 Way Toggle Switch 3A/5A AC 250V/125V DPDT On Off, 250v for DIY
You must be logged in to post a review.
Related products
CD4017-4017 Cd4017 Cd4017Be Cmos Decade Counter with 10 Decoded Outputs Dip16 IC
₹20.00₹13.94 + GSTPurchase & earn 14 SmartX Rewards Coin!Add to cartBuy now- Decade counter/decimal decode display (CD4017B)
- Binary counter/decoder
- Frequency division
- Counter control/timers
- Divde-by-N counting
- For further application information, see ICAN-6166 “COS/MOS MSI Counter and Register Design and Applications”
- Rated 5.00 out of 5
5V Low Level Solid State Relay Module with Fuse SSR 250V 2A Fuse
₹150.00₹110.00 + GSTPurchase & earn 110 SmartX Rewards Coin!Add to cartBuy now1-Channel?Solid-State Relay is some what similar to that of a mechanical relay & the difference is that, there is no moving contact in a Solid-State Relay. Here we make use of Phototropic coupler to turn it ON and OFF.
- Rated 4.17 out of 5
Single Channel 5v Relay Module with Isolation High Low Level Trigger
₹40.00₹39.00 + GSTPurchase & earn 39 SmartX Rewards Coin!Add to cartBuy nowRelays are output devices which are used to control or operate some external devices.? This is a 5 volt Isolated relay module which means that there is a optocoupler used in between your control circuit and the relay thus protecting your circuit in case of any short circuit issues on the relay side.
- Purchase & earn 2 SmartX Rewards Coin!Add to cartBuy now
BC327 is a general purpose PNP BJP transistor that can be used for switching and amplification purposes in electronic circuits. The transistor features 800mA collector current hence it can be used to drive variety of loads in an electronic application. The max collector-emitter voltage is -45V therefore it can easily handle load voltage under 45V. Apart from that transistor also features 625mW collector dissipation and DC current gain of maximum 630 therefore it can also be used as an audio amplifier or for any type of signal amplification.
- Rated 5.00 out of 5
8 Channel 5V Relay Board Expansion Module Optocoupler compatible UNO Raspberry
₹312.00₹246.16 + GSTPurchase & earn 246 SmartX Rewards Coin!Add to cartBuy nowSpecification
- This relay module is 5 Volts active low.
- It is an 8-channel relay interface board, which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, PLC, etc.
- It is also able to control various appliances and other equipments with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Standard interface can be directly connected with microcontrollers.
- Red working status indicator lights are conducive to the safe use.
- Widely used for all MCU control, industrial sector, PLC control, smart home control.
- Input port IN1, IN2, IN3, IN4, IN5, IN6, IN7, IN8 low signal level effectively.
- VCC, GND : Input power.
- JD – VCC : Relay power input port,relay can power alone.
- Working voltage : 5V
- Module weight : about 112g
- package weight : about 150g
- module size : about 1.7cm X 5.5cm X 13.7cm(height * width * long)
Roma (verified owner) –
I got my project done with these components Great Support