40 Pin Female Header Berg Strip – Break Away Header
₹10.73
This 40 Pin Female Break Away Header has the industry standard spacing of 2.54mm and are designed for soldering directly into printed circuit boards (PCB). They are supplied Best for extension of pins of Microcontorllers and ICs
70 in stock
This 40 Pin Female Break Away Header has the industry standard spacing of 2.54mm and are designed for soldering directly into printed circuit boards (PCB). They are supplied Best for extension of pins of Microcontorllers and ICs
Related products
- Add to cart
This DC Voltage Sensor Module is essentially a 5:1 potential divider circuit built using precession resistors for high accuracy.
The Arduino analog input is limited to a 5 VDC input. If you wish to measure higher voltages,this module allows you to measure voltages of 0-25V. Keep in mind, you are restricted to voltages that are less than 25 volts. More than that and you will exceed the voltage limit of your Arduino input.
- Rated 4.58 out of 5
3.7V 1200 mAh Li-ion Cylindrical Battery | 3.7V Lithium Ion Battery for DIY Projects | Lithium Ion Cylindrical Battery
₹90.00₹60.00Add to cartA lithium-ion battery or Li-ion battery is a type of rechargeable battery. Lithium-ion batteries are commonly used for portable electronics and electric vehicles and are growing in popularity for military and aerospace applications.
- Read more
Specification
- Size : 75mm (length) x 55mm (W) x 19.3mm (height);
- Weight : 80g;
- PCB Color : Blue;
- board four weeks with four screw holes, hole diameter 3.1mm, easy to install and fixed;
- Relay selection of quality loose music relays, SPDT. A common terminal, a normally open, one normally closed terminal;
- optocoupler isolation, good anti-jamming;
- Low pull, high release. Energisation status indicator light, release status LED is off;
- VCC for the system power, JD_VCC for the relay power. Default hair 12V relay, plug the jumper cap to;
- Relay Maximum output : DC 30V/10A, AC 250V/10A
- Wiring : VCC : positive power supply system GND : System power supply negative IN1 – IN4 : relay control ports
- Rated 5.00 out of 5
8 Channel 5V Relay Board Expansion Module Optocoupler compatible UNO Raspberry
₹312.00₹300.20Add to cartSpecification
- This relay module is 5 Volts active low.
- It is an 8-channel relay interface board, which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, PLC, etc.
- It is also able to control various appliances and other equipments with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Standard interface can be directly connected with microcontrollers.
- Red working status indicator lights are conducive to the safe use.
- Widely used for all MCU control, industrial sector, PLC control, smart home control.
- Input port IN1, IN2, IN3, IN4, IN5, IN6, IN7, IN8 low signal level effectively.
- VCC, GND : Input power.
- JD – VCC : Relay power input port,relay can power alone.
- Working voltage : 5V
- Module weight : about 112g
- package weight : about 150g
- module size : about 1.7cm X 5.5cm X 13.7cm(height * width * long)
- Add to cart
BC557 is a widely used PNP bipolar junction transistor manufactured in small TO-92 package. It is a general purpose PNP transistor that can be used as a switch or amplifier in electronic circuits. Its HFE ratings are 125 to 800 which makes it an ideal transistor to use as a small signal amplifier in electronic circuits for example for audio signal amplification or other, the HFE ratings of BC557 can be determined by the last letter after its number for example BC557A HFE ratings are 110-220, BC557B HFE ratings are 200-450 and BC557C HFE ratings are 420-800. The max collector dissipation is 500 milliwatt which is also an another good point to use it in amplification stages. Moreover it will also perform well when used it as a switch for load under 100mA. The transistor has also good collector to emitter (VCE) value that is -45V, therefore you can easily use it in circuits using 40 to 45 volts DC.
Reviews
There are no reviews yet.