2k 100W Ohm Variable Resistor
₹300.00 ₹204.18 + GST
3 in stock
Purchase & earn 204 SmartX Rewards Coin!Type : Adjustable
Rated Power : 100W
Resistance : 2K ?;
Diameter in CM:? 3 cm
Length In CM : 15 cm
Inner Diameter : 2cm
Color : Green
Material : Metal, Ceramic
You must be logged in to post a review.
Related products
- Purchase & earn 7 SmartX Rewards Coin!Add to cartBuy now
This is a 8MHZ Crystal. This is a low cost crystal oscillator with?oscillation frequency of 8Mhz. Crystal are normally required to provide?clock pulses to your micro controller or other IC’s which require external clock?source.
An oscillator crystal has two electrically conductive plates, with a slice or?tuning fork of quartz crystal sandwiched between them. The crystal oscillator?circuit sustains oscillation by taking a voltage signal from the quartz?resonator, amplifying it, and feeding it back to the resonator. Quartz has the?further advantage that its elastic constants and its size change in such a way?that the frequency dependence on temperature can be very low.
- Rated 5.00 out of 5
8 Channel 5V Relay Board Expansion Module Optocoupler compatible UNO Raspberry
₹312.00₹246.16 + GSTPurchase & earn 246 SmartX Rewards Coin!Add to cartBuy nowSpecification
- This relay module is 5 Volts active low.
- It is an 8-channel relay interface board, which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, PLC, etc.
- It is also able to control various appliances and other equipments with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Standard interface can be directly connected with microcontrollers.
- Red working status indicator lights are conducive to the safe use.
- Widely used for all MCU control, industrial sector, PLC control, smart home control.
- Input port IN1, IN2, IN3, IN4, IN5, IN6, IN7, IN8 low signal level effectively.
- VCC, GND : Input power.
- JD – VCC : Relay power input port,relay can power alone.
- Working voltage : 5V
- Module weight : about 112g
- package weight : about 150g
- module size : about 1.7cm X 5.5cm X 13.7cm(height * width * long)
- Purchase & earn 1 SmartX Rewards Coins!Add to cartBuy now
BC547 is a general purpose BJT NPN transistor mostly used in electronics hobbyists and educational electronics projects. Besides these uses it can also be used in commercial circuits. It comes in TO-92 packaging and the maximum output current this transistor can handle is 100mA. The transistor is having very good DC current gain and low noise capabilities due to which it is ideal to use in signal amplification stages. The typical saturation voltage is only 90 millivolts which is also a good sign to use it as a switch.
- Purchase & earn 15 SmartX Rewards Coin!Add to cartBuy now
This DC Voltage Sensor Module is essentially a 5:1 potential divider circuit built using precession resistors for high accuracy.
The Arduino analog input is limited to a 5 VDC input.? If you wish to measure higher voltages,this module allows you to measure voltages of 0-25V. Keep in mind, you are restricted to voltages that are less than 25 volts. More than that and you will exceed the voltage limit of your Arduino input.
- Purchase & earn 2 SmartX Rewards Coin!Add to cartBuy now
This is a?100 x 2.5 mm Nylon cable tie?also known as hose tie or Zip tie. The?cable tie?is perfect for holding items together specially electric cables or wires.? The flexible design of the?cable tie?makes it easier to slip the ties under and around wire harness. Thanks to the teeth on one of the side of the belt makes it easier for self locking and securing the wires.
Reviews
There are no reviews yet.