14 Pin DIP IC Base-Socket-Base-Connector for Microcontrollers and IC’s/IC base-base IC
₹5.00 Original price was: ₹5.00.₹2.71Current price is: ₹2.71. + GST
14 Pin IC Socket base adaptor is a 14 pin IC holder, which can be soldered directly onto the PCB. The IC can be removed from this socket when required. The IC is placed on the socket at the time of use. This base acts as a removable IC holder.
431 in stock
Purchase & earn 3 SmartX Rewards Coin!- 14 pins.
- JDEC compliant.
- Molded notch for proper orientation.
- Easy to insert and remove ICs.
12 reviews for 14 Pin DIP IC Base-Socket-Base-Connector for Microcontrollers and IC’s/IC base-base IC
You must be logged in to post a review.
Related products
- Rated 4.00 out of 5
BC327 PNP General Purpose Amplifier Transistor
₹5.00Original price was: ₹5.00.₹1.95Current price is: ₹1.95. + GSTPurchase & earn 2 SmartX Rewards Coin!Add to cartBuy nowBC327 is a general purpose PNP BJP transistor that can be used for switching and amplification purposes in electronic circuits. The transistor features 800mA collector current hence it can be used to drive variety of loads in an electronic application. The max collector-emitter voltage is -45V therefore it can easily handle load voltage under 45V. Apart from that transistor also features 625mW collector dissipation and DC current gain of maximum 630 therefore it can also be used as an audio amplifier or for any type of signal amplification.
- Rated 4.00 out of 5
Crystal Oscillator 8 MHZ
₹15.00Original price was: ₹15.00.₹6.72Current price is: ₹6.72. + GSTPurchase & earn 7 SmartX Rewards Coin!Add to cartBuy nowThis is a 8MHZ Crystal. This is a low cost crystal oscillator with?oscillation frequency of 8Mhz. Crystal are normally required to provide?clock pulses to your micro controller or other IC’s which require external clock?source.
An oscillator crystal has two electrically conductive plates, with a slice or?tuning fork of quartz crystal sandwiched between them. The crystal oscillator?circuit sustains oscillation by taking a voltage signal from the quartz?resonator, amplifying it, and feeding it back to the resonator. Quartz has the?further advantage that its elastic constants and its size change in such a way?that the frequency dependence on temperature can be very low.
- Rated 5.00 out of 5
8 Channel 5V Relay Board Expansion Module Optocoupler compatible UNO Raspberry
₹312.00Original price was: ₹312.00.₹246.16Current price is: ₹246.16. + GSTPurchase & earn 246 SmartX Rewards Coin!Add to cartBuy nowSpecification
- This relay module is 5 Volts active low.
- It is an 8-channel relay interface board, which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, PLC, etc.
- It is also able to control various appliances and other equipments with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Standard interface can be directly connected with microcontrollers.
- Red working status indicator lights are conducive to the safe use.
- Widely used for all MCU control, industrial sector, PLC control, smart home control.
- Input port IN1, IN2, IN3, IN4, IN5, IN6, IN7, IN8 low signal level effectively.
- VCC, GND : Input power.
- JD – VCC : Relay power input port,relay can power alone.
- Working voltage : 5V
- Module weight : about 112g
- package weight : about 150g
- module size : about 1.7cm X 5.5cm X 13.7cm(height * width * long)
Optocoupler High Level Relay Module Board 5V 4-CH for PIC ARM DSP AVR | Compatible with Arduno NodeMCU Raspberry Pi | Pack of 1 | Blue (Excellent Quality)
₹139.00Original price was: ₹139.00.₹136.50Current price is: ₹136.50. + GSTPurchase & earn 137 SmartX Rewards Coin!Add to cartBuy nowSpecification
- Size : 75mm (length) x 55mm (W) x 19.3mm (height);
- Weight : 80g;
- PCB Color : Blue;
- board four weeks with four screw holes, hole diameter 3.1mm, easy to install and fixed;
- Relay selection of quality loose music relays, SPDT. A common terminal, a normally open, one normally closed terminal;
- optocoupler isolation, good anti-jamming;
- Low pull, high release. Energisation status indicator light, release status LED is off;
- VCC for the system power, JD_VCC for the relay power. Default hair 12V relay, plug the jumper cap to;
- Relay Maximum output : DC 30V/10A, AC 250V/10A
- Wiring : VCC : positive power supply system GND : System power supply negative IN1 ? IN4 : relay control ports
- Rated 5.00 out of 5
16 x 2 (JHD162A) Blue/White color DC 5V Character LCD display module FOR ALL TYPE OF DEVLOMENT BOARD
₹200.00Original price was: ₹200.00.₹96.76Current price is: ₹96.76. + GSTPurchase & earn 97 SmartX Rewards Coin!Add to cartBuy now- Operating Voltage is 4.7V to 5.3V
- Current consumption is 1mA without backlight
- Alphanumeric LCD display module, meaning can display alphabets and numbers
- Consists of two rows and each row can print 16 characters.
- Each character is build by a 5?8 pixel box
- Can work on both 8-bit and 4-bit mode
- It can also display any custom generated characters
- Available in Blue Backlight
Ketan (verified owner) –
Less cost than other websites
Priya (verified owner) –
Very well worth the money.
Priya (verified owner) –
Online best cost electronic components
Komal (verified owner) –
I got my project done with these components Great Support
Shubham (verified owner) –
Good techinical knowledge
Shubham (verified owner) –
I got my project done with these components Great Support
Roma (verified owner) –
Very well worth the money.
Paaji (verified owner) –
Good techinical knowledge
Shubham (verified owner) –
Good support and recommended
Sneha (verified owner) –
The product is firmly packed.
Prakash (verified owner) –
Drone parts i ordered and found ok
Paaji (verified owner) –
Very fast delivery.