

6 Pin 2 Way Toggle Switch 3A/5A AC 250V/125V DPDT On Off, 250v for DIY
₹30.00 ₹19.75
It is a Mini MTS-203 6-Pin DPDT 6A 125VAC Toggle Switch. The switch is Double Pole Double Throw with 6 pins.
28 in stock
Purchase & earn 20 SmartX Rewards Coin!1 review for 6 Pin 2 Way Toggle Switch 3A/5A AC 250V/125V DPDT On Off, 250v for DIY
You must be logged in to post a review.
Related products
- Rated 5.00 out of 5
8 Channel 5V Relay Board Expansion Module Optocoupler compatible UNO Raspberry
₹312.00₹246.16 + GSTPurchase & earn 246 SmartX Rewards Coin!Add to cartSpecification
- This relay module is 5 Volts active low.
- It is an 8-channel relay interface board, which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, PLC, etc.
- It is also able to control various appliances and other equipments with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Standard interface can be directly connected with microcontrollers.
- Red working status indicator lights are conducive to the safe use.
- Widely used for all MCU control, industrial sector, PLC control, smart home control.
- Input port IN1, IN2, IN3, IN4, IN5, IN6, IN7, IN8 low signal level effectively.
- VCC, GND : Input power.
- JD – VCC : Relay power input port,relay can power alone.
- Working voltage : 5V
- Module weight : about 112g
- package weight : about 150g
- module size : about 1.7cm X 5.5cm X 13.7cm(height * width * long)
- Rated 4.67 out of 5
DHT11 Module Temperature and Humidity sensor Module for boards compatible with Arduino, ARM and other MCU
₹120.00₹88.05 + GSTPurchase & earn 88 SmartX Rewards Coin!Add to cartThe DHT11 is a commonly used Temperature and humidity sensor. The sensor comes with a dedicated NTC to measure temperature and an 8-bit microcontroller to output the values of temperature and humidity as serial data. The sensor is also factory calibrated and hence easy to interface with other microcontrollers.
- Purchase & earn 2 SmartX Rewards Coin!Add to cart
BC327 is a general purpose PNP BJP transistor that can be used for switching and amplification purposes in electronic circuits. The transistor features 800mA collector current hence it can be used to drive variety of loads in an electronic application. The max collector-emitter voltage is -45V therefore it can easily handle load voltage under 45V. Apart from that transistor also features 625mW collector dissipation and DC current gain of maximum 630 therefore it can also be used as an audio amplifier or for any type of signal amplification.
- Rated 4.48 out of 5
5.5mm x 2.1mm 3 Pin Female DC Power Jack Panel Mount Screw Nut Kit DC Socket Electrical Plug
₹20.00₹8.20 + GSTPurchase & earn 8 SmartX Rewards Coin!Add to cart- Widely used in small-scale as well as prototyping projects where 12 to 30 volts power supply needed
- Supports DC Power Jack: 2.1 x 5.5 mm
- Diameter: 14mm
- Purchase & earn 277 SmartX Rewards Coin!Add to cart
Flex sensors are usually available in two sizes. One is 2.2 inch and another is 4.5 inch. Although the sizes are different the basic function remains the same. They are also divided based on resistance. There are LOW resistance, MEDIUM resistance and HIGH resistance types. Choose the appropriate type depending on requirement. ?Here we are going to discuss 2.2inch Flex sensor that is FS-L-0055.
Roma (verified owner) –
I got my project done with these components Great Support