

12V PCB Mount Sugar Cube SPDT Relay
₹25.22 ₹21.02 + GST
- Voltage: 12V
- Rated with:
- 7A/240VAC
- 7A/14VDC
- 7.5A/250AC
- Fully sealed
- Compact size
164 in stock
Purchase & earn 21 SmartX Rewards Coin!- Product type: SPDT sugar cube relay
- Voltage: 12v
- Number of pins: 5
- Pin type: through hole
- Package contains: 1 X sugar cube SPDT relay switch
2 reviews for 12V PCB Mount Sugar Cube SPDT Relay
You must be logged in to post a review.
Related products
- Rated 4.56 out of 5
Quartz Crystal Oscillator 16MHz HC-49S 2 Pin for TV, car Electronics, PC Card, Electronic Watch, DVD, MP3v
₹15.00₹6.72 + GSTPurchase & earn 7 SmartX Rewards Coin!Add to cartCrystal Oscillators are used as a quick and easy way to offer circuits a very accurate and consistent frequency output. This 16 MHz Crystal is a thru-hole type and is typically used with microcontrollers. - Purchase & earn 1 SmartX Rewards Coins!Add to cart
BC557 is a widely used PNP bipolar junction transistor manufactured in small TO-92 package. It is a general purpose PNP transistor that can be used as a switch or amplifier in electronic circuits. Its HFE ratings are 125 to 800 which makes it an ideal transistor to use as a small signal amplifier in electronic circuits for example for audio signal amplification or other, the HFE ratings of BC557 can be determined by the last letter after its number for example BC557A HFE ratings are 110-220, BC557B HFE ratings are 200-450 and BC557C HFE ratings are 420-800. The max collector dissipation is 500 milliwatt which is also an another good point to use it in amplification stages. Moreover it will also perform well when used it as a switch for load under 100mA. The transistor has also good collector to emitter (VCE) value that is -45V, therefore you can easily use it in circuits using 40 to 45 volts DC.
- Rated 5.00 out of 5
8 Channel 5V Relay Board Expansion Module Optocoupler compatible UNO Raspberry
₹312.00₹246.16 + GSTPurchase & earn 246 SmartX Rewards Coin!Add to cartSpecification
- This relay module is 5 Volts active low.
- It is an 8-channel relay interface board, which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, PLC, etc.
- It is also able to control various appliances and other equipments with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Standard interface can be directly connected with microcontrollers.
- Red working status indicator lights are conducive to the safe use.
- Widely used for all MCU control, industrial sector, PLC control, smart home control.
- Input port IN1, IN2, IN3, IN4, IN5, IN6, IN7, IN8 low signal level effectively.
- VCC, GND : Input power.
- JD – VCC : Relay power input port,relay can power alone.
- Working voltage : 5V
- Module weight : about 112g
- package weight : about 150g
- module size : about 1.7cm X 5.5cm X 13.7cm(height * width * long)
- Rated 4.67 out of 5
DHT11 Module Temperature and Humidity sensor Module for boards compatible with Arduino, ARM and other MCU
₹120.00₹88.05 + GSTPurchase & earn 88 SmartX Rewards Coin!Add to cartThe DHT11 is a commonly used Temperature and humidity sensor. The sensor comes with a dedicated NTC to measure temperature and an 8-bit microcontroller to output the values of temperature and humidity as serial data. The sensor is also factory calibrated and hence easy to interface with other microcontrollers.
- Purchase & earn 277 SmartX Rewards Coin!Add to cart
Flex sensors are usually available in two sizes. One is 2.2 inch and another is 4.5 inch. Although the sizes are different the basic function remains the same. They are also divided based on resistance. There are LOW resistance, MEDIUM resistance and HIGH resistance types. Choose the appropriate type depending on requirement. ?Here we are going to discuss 2.2inch Flex sensor that is FS-L-0055.
Viral (verified owner) –
Good service.
Shubham (verified owner) –
Very fast delivery.